- 您現在的位置：買賣IC網 > PDF目錄1954 > MCZ33797EKR2 (Freescale Semiconductor)IC SQUIB DRIVER 2CHAN 32-SOIC PDF資料下載
參數資料
| 型號： | MCZ33797EKR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 14/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SQUIB DRIVER 2CHAN 32-SOIC |
| 標準包裝： | 1,000 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33797
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
TX: Request another command sequence.
RX: Receive loop-to-loop results from test.
CROSS-COUPLED SQUIB IC FUNCTION
The cross-coupled application utilizes the high and low side
squib drivers from two different squib driver ICs (see
SPI interface, the squib IC will maintain the capability to
conduct standard diagnostics (short-to-battery, short-to-
ground, short between squibs, and squib diagnostics)
between two different squib ICs. The squib IC must maintain
the capability to fire the squib drivers with the ARM and FIRE
command in either cross-coupled or single IC applications.
When the firing squib driver IC is used in cross-coupled
applications, the low side squib driver must be activated prior
to activating the high side squib driver.
Cross-coupling the high and low side squib driver from two
different squib driver ICs must be done without interfering
with standard squib operations when the squib IC is used in
an application where the high and low side squib drivers are
located on the same IC.
All remaining diagnostic functions will operate standard in
either a cross-coupled or single IC applications. These
functions include RR_DIAG, RR_LIMIT_X, high side, VVFIRE_XX,
VVFIRE_RTN, VTRANSTX, squib current timing measurement,
and FEN_1 and FEN_2 diagnostics.
The SENSE_1A (1B, 2A, or 2B) pin squib IC #1 is connected
to SQB_LO_1A (1B, 2A, or 2B) pin squib driver IC #2 and is
used to feed the diagnostic signal for determining squib
resistance and short-to-battery/ground conditions (see
passes from squib driver IC #1 high side driver though the
squib to squib driver IC #2 low side driver. In the cross-
coupled mode, the squib driver IC #2 $C2
(SQUIB_LO_1A_CONT, [1B, 2A, or 2B]) command will be
used to check continuity of the low side driver from the
SQB_LO_1A (1B, 2A, or 2B) pin to the low side driver FET.
The low side driver continuity is checked during the continuity
test. The driver continuity information will be cleared after the
information is transmitted on the next valid SPI command.
EXAMPLE—CROSS-COUPLED SQUIB COMMAND
SPI SEQUENCE FROM MICROCONTROLLER
TX: Squib IC #1 request squib 1A resistance measurement
($D0).
RX: Previous executed command information.
TX: Run another command on the same squib IC #1.
RX: Receive measured squib 1A resistance information.
TX: Squib IC #1 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Receive low side driver continuity information for low
side drivers which reside on IC #2.
TX: Squib IC #1 request another command sequence.
RX: Receive low side driver continuity information for low
side drivers that reside on IC #1.
TX: Squib IC #1 request loop-to-loop short command
($E0–$E3)
RX: Previous executed command information.
TX: Squib IC #2 request loop to loop short command for
other ICs ($E8).
RX: Previous executed command information.
TX: Squib IC #2 request loop-to-loop short command for
other ICs ($E8).
RX: Receive loop-to-loop results from test run on IC #1.
TX: Squib IC #1 request another command sequence.
RX: Receive loop-to-loop results from test run on IC #1.
FIRING A SQUIB
The firing of a squib driver requires the FEN_1 and FEN_2
pins to be high and two separate 8-bit writes be made to the
shift register. With FEN_1 pin high, squibs 1A and 1B can be
armed and fired. With FEN_2 pin high, squibs 2A and 2B can
be armed and fired. The first write is to ARM squib drivers in
preparation of receiving the fire command. Squib 1A and
squib 1B can be armed separately from squib 2A and
squib 2B (refer to Table 7) or all squibs can be fired at once
(refer to Table 8). All ARM and 5X (Fire) commands will be
echoed back on the SPI Data output.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
| MCZ33972EWR2 | IC SWITCH DETECTION MULT 32-SOIC |
| MCZ33975AEKR2 | IC SWITCH DETECT MULT ENH 32SOIC |
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33800EK | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
發布緊急采購，3分鐘左右您將得到回復。