- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33797EK (飛思卡爾半導體(中國)有限公司) Four Channel Squib Driver IC PDF資料下載
參數資料
| 型號： | MCZ33797EK |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Four Channel Squib Driver IC |
| 中文描述： | 四通道爆管驅動IC |
| 文件頁數： | 17/34頁 |
| 文件大?。?/td> | 290K |
| 代理商： | MCZ33797EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
33797
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
SQUIB SENSE XX (SENSE_XX)
The Sense pins are used
exclusively
for diagnostics
related to the squib, driver FETs, or harness. Commands
using the Sense pins include:
C1, C2, C3, C9
D<3:0>
E<3:0>
E9
82/1x
83/2x
Independent of the system configuration, normal or cross
coupled, the Sense pin, xx and
SquibHi, xx of a single IC are
always
connected to the
same
squib with the SquibHi pin
connected to the high pin of the squib and the Sense pin
connected to the low pin of the squib. A cross coupled
configuration is achieved by
only cross coupling
the squib low
pins. See
Figure 8
and
Figure 9
.
STANDARD APPLICATIONS
In the standard mode, the $C2 (SQUIB_LO_XX_CONT)
command will be used to check continuity of the low-side
driver from the SQB_LO_XX pin to the high-side driver FET
(see
Figure 6
).
CROSS-COUPLED APPLICATIONS
Used during cross-coupling applications involving two
four-channel squib driver ICs (squib driver IC #1 and squib
driver IC #2). SENSE_XX pins from squib driver IC #1 are
connected to their respective squib minus pins (Squib Low
SQB_LO_XX) from squib driver IC #2 (
Figure 9
).
SENSE_XX pins are used to feed diagnostic signals back to
squib driver IC #1 for determining squib resistance, short-to-
battery/ground, and squib loop-to-loop short conditions.
During a fire event, the fire current passes from squib driver
IC #1 high-side driver though the squib to squib driver IC #2
low-side driver (
Figure 9
). In the cross-coupled mode, the
squib driver IC #2 $C2 (SQUIB_LO_XX_CONT) command
will be used to check continuity of the low-side driver from the
SQB_LO_XX pin to the low-side driver FET.
DESIGN NOTES
Diagnostics always have the form of a f
orcing function
and
a
measurement or sense function
. In a cross couple
configuration, most diagnostics are unaffected and are single
commands except for $C2 Low Side FET Continuity and
$E<3:0> Harness Shorts, and 83/2x Low- Side FET test. This
command must be sent to each IC to be executed. For these
three diagnostics, two commands are required because the
forcing function
and
sensing function
are on separate ICs.
Harness Shorts Diagnostics: Force using $E<3:0> on
IC#1, Sense $E8 on IC2
Low-Side FET Continuity: Force using $C1 on IC#1,
Sense using $C2 on IC#2
Low-Side FET Test: Force using $C1 on IC#1, Sense
using $C2 on IC#2
An active 600
μ
A current sink is located in the SENSE_XX
pin. The sink current is used to pull the charge off of the
external EMC ilter caps after a diagnostic measurement has
been made.
SQUIB HI XX (SQB
_
HI
_
XX)
Squib high pins for squibs 1A, 1B, 2A, and 2B. These pins
are connected to the sources of the high-side FET drivers, as
well as the diagnostic circuitry.
SQUIB LOW XX (SQB
_
LO
_
XX)
Squib low pins for squibs 1A, 1B, 2A, and 2B. These pins
are connected to the drains of the low-side FET drivers, as
well as the diagnostic circuitry.
SQUIB FIRING SUPPLY XX (VFIRE_XX)
Firing supply pins for squibs 1A, 1B, 2A, and 2B. These
pins are connected to the drains of the high-side FET drivers.
Feedback for high-side safing for squibs 1A and 1B will be
referenced from VFIRE_1A and squibs 2A and 2B from
VFIRE_2A. For high-side safing, VFIRE_1B should be
connected to VFIRE_1A pin and VFIRE_2B to VFIRE_2A
pin.
SQUIB FIRE POWER GROUND (VFIRE_RTN)
Return for squibs 1A, 1B, 2A AND 2B. The pins are tied to
the source pins of both low-side FET drivers, as well as the
diagnostic circuitry. The RTN pins are tied internally.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33800EK | Engine Control Integrated Circuit |
| MCZ33879AEK | Configurable Octal Serial Switch with Open Load Detect Current Disable |
| MCZ33880EG | Configurable Octal Serial Switch with Serial Peripheral Interface I/O |
| MCZ33883EG | H-Bridge Gate Driver IC |
| MCZ33884EG | Switch Monitor Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33797EKR2 | 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33800EK | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。