- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33399EF (飛思卡爾半導體(中國)有限公司) Local Interconnect Network (LIN) Physical Interface PDF資料下載
參數資料
| 型號： | MCZ33399EF |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Local Interconnect Network (LIN) Physical Interface |
| 中文描述： | 本地互連網絡（LIN）物理接口 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 234K |
| 代理商： | MCZ33399EF |
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
33399
FUNCTIONAL DESCRIPTION
TIMING DIAGRAMS
INHIBIT OUTPUT PIN (INH)
The INH pin controls an external switchable voltage
regulator having an inhibit input. This pin is a high-side switch
structure to V
SUP
. When the device is in the Normal mode,
the inhibit high-side switch is turned ON and the external
voltage regulator is activated. When the device is in Sleep
mode, the inhibit switch is turned OFF and disables the
voltage regulator (if this feature is used).
A wake-up event on the LIN bus line will switch the INH pin
to V
SUP
level. Wake-up output current capability is limited to
280 μA. INH can also drive an external MOSFET connected
to an MCU IRQ or XIRQ input to generate an interrupt. See
the typical application illustrated in
Figure 13
, page
15
.
WAKE INPUT PIN (WAKE)
The WAKE pin is a high-voltage input used to wake up the
device from Sleep mode. WAKE is usually connected to an
external switch in the application. The typical WAKE
thresholds are V
SUP
/ 2.
The WAKE pin has a special design structure and allows
wake-up from both HIGH-to-LOW or LOW-to-HIGH
transitions. When entering the Sleep mode, the LIN monitors
the state of the WAKE pin and stores it as a reference state.
The opposite state of this reference state will be the wake-up
event used by the device to re-enter Normal mode.
An internal filter is implemented (50
μ
s typical filtering time
delay). The WAKE pin input structure exhibits a high
impedance with extremely low input current when voltage at
this pin is below 14 V. When voltage at the WAKE pin
exceeds 14 V, input current starts to sink into the device. A
series resistor should be inserted in order to limit the input
current, mainly during transient pulses. Recommended
resistor value is 33 k
.
Important
The WAKE pin should
not
be left open. If the
wake-up function is not used, WAKE should be connected to
GND to avoid false wake-up.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33661EF | Local Area Network (LIN) Enhanced Physical Interface with Selectable Slew Rate |
| MCZ33689DEW | System Basis Chip with LIN Transceiver |
| MCZ33742EG | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver |
| MCZ33790EG | Two-Channel Distributed System Interface (DSI) Physical Interface Device |
| MCZ33793AEF | Distributed System Interface (DSI) Sensor Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33399EFR2 | 功能描述:輸入/輸出控制器接口集成電路 LIN INTERFACE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MCZ33661EF | 功能描述:網絡控制器與處理器 IC ENHANCED LIN INTERFACE RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33661EF | 制造商:Freescale Semiconductor 功能描述:IC INTERFACE PHYSICAL LINE 8SOIC |
| MCZ33661EFR2 | 功能描述:網絡控制器與處理器 IC ENHANCED LIN INTERFACE RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33661EFR2 | 制造商:Freescale Semiconductor 功能描述:IC LIN INTERFACE 制造商:Freescale Semiconductor 功能描述:IC, LIN INTERFACE |
發布緊急采購，3分鐘左右您將得到回復。