- 您現在的位置：買賣IC網 > PDF目錄69032 > MCV14AI/P 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDIP14 PDF資料下載
參數資料
| 型號： | MCV14AI/P |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDIP14 |
| 封裝： | 0.300 INCH, ROHS COMPLIANT, PLASTIC, DIP-14 |
| 文件頁數： | 22/84頁 |
| 文件大?。?/td> | 1007K |
| 代理商： | MCV14AI/P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
2009 Microchip Technology Inc.
Preliminary
DS41338B-page 27
MCV14A
5.5
I/O Programming Considerations
5.5.1
BIDIRECTIONAL I/O PORTS
Some instructions operate internally as read followed
by write operations. The BCF and BSF instructions, for
example, read the entire port into the CPU, execute the
bit operation and rewrite the result. Caution must be
used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a BSF operation on bit 5 of PORTB will cause
all eight bits of PORTB to be read into the CPU, bit 5 to
be set and the PORTB value to be written to the output
latches. If another bit of PORTB is used as a bidirec-
tional I/O pin (say bit 0) and it is defined as an input at
this time, the input signal present on the pin itself would
be read into the CPU and rewritten to the data latch of
this particular pin, overwriting the previous content. As
long as the pin stays in the Input mode, no problem
occurs. However, if bit 0 is switched into Output mode
later on, the content of the data latch may now be
unknown.
Example 5-1 shows the effect of two sequential
Read-Modify-Write instructions (e.g., BCF, BSF, etc.)
on an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired OR”, “wired
AND”). The resulting high output currents may damage
the chip.
EXAMPLE 5-1:
READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT(e.g., MCV14A)
5.5.2
SUCCESSIVE OPERATIONS ON
I/O PORTS
The actual write to an I/O port happens at the end of an
instruction cycle, whereas for reading, the data must be
valid at the beginning of the instruction cycle (Figure 5-2).
Therefore, care must be exercised if a write followed by
a read operation is carried out on the same I/O port. The
sequence of instructions should allow the pin voltage to
stabilize (load dependent) before the next instruction
causes that file to be read into the CPU. Otherwise, the
previous state of that pin may be read into the CPU rather
than the new state. When in doubt, it is better to separate
these instructions with a NOP or another instruction not
accessing this I/O port.
FIGURE 5-2:
SUCCESSIVE I/O OPERATION
;Initial PORTB Settings
;PORTB<5:3> Inputs
;PORTB<2:0> Outputs
;
PORTB latch
PORTB pins
;
----------
BCF
PORTB, 5 ;--01 -ppp
--11 pppp
BCF
PORTB, 4 ;--10 -ppp
--11 pppp
MOVLW
007h;
TRIS
PORTB
;--10 -ppp
--11 pppp
;
Note
1:
The user may have expected the pin values to
be ‘--00 pppp’. The 2nd BCF caused RB5 to
be latched as the pin value (High).
PC
PC + 1
PC + 2
PC + 3
Q1 Q2
Q3 Q4
Q1 Q2 Q3 Q4
Q1
Q2 Q3 Q4
Q1 Q2
Q3 Q4
Instruction
Fetched
RB<5:0>
MOVWF PORTB
NOP
Port pin
sampled here
NOP
MOVF PORTB
, W
Instruction
Executed
MOVWF PORTB
(Write to PORTB)
NOP
MOVF PORTB,W
This example shows a write to PORTB
followed by a read from PORTB.
Data setup time = (0.25 TCY – TPD)
where: TCY = instruction cycle.
TPD = propagation delay
Therefore, at higher clock frequencies, a
write followed by a read may be problematic.
(Read PORTB)
Port pin
written here
相關PDF資料 |
PDF描述 |
|---|---|
| MD8031AHB883B | 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40 |
| MD8255A | 24 I/O, PIA-GENERAL PURPOSE, PDIP40 |
| MD82C52-/883 | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, CDIP28 |
| MR82C52-/883 | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, CQCC28 |
| MD82C55A-5/B | 24 I/O, PIA-GENERAL PURPOSE, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCV15/10-GF-381 | 制造商:Phoenix Contact 功能描述:HEADER PCB VERTICAL 3.81MM 10WAY |
| MCV15/2-GF-381 | 制造商:Phoenix Contact 功能描述:HEADER PCB VERTICAL 3.81MM 2WAY |
| MCV15/3-GF-381 | 制造商:Phoenix Contact 功能描述:HEADER PCB VERTICAL 3.81MM 3WAY |
| MCV15/4-GF-381 | 制造商:Phoenix Contact 功能描述:HEADER PCB VERTICAL 3.81MM 4WAY |
| MCV15/5-GF-381 | 制造商:Phoenix Contact 功能描述:HEADER PCB VERTICAL 3.81MM 5WAY |
發布緊急采購，3分鐘左右您將得到回復。