- 您現在的位置：買賣IC網 > PDF目錄9399 > MCP7940M-I/MS (Microchip Technology)IC RTCC 64B I2C SRAM 8-MSOP PDF資料下載
參數資料
| 型號： | MCP7940M-I/MS |
| 廠商： | Microchip Technology |
| 文件頁數： | 5/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTCC 64B I2C SRAM 8-MSOP |
| 標準包裝： | 100 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，方波輸出，SRAM |
| 存儲容量： | 64B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
Micrel, Inc.
SY69754AL
August 2007
13
M9999-082107-E
hbwhelp@micrel.com or (408) 955-1690
Appendix A
Layout and General Suggestions
1.
Establish controlled impedance stripline, microstrip, or
coplanar construction techniques.
2.
Signal paths should have approximately the same width
as the device pads.
3.
All differential paths are critical timing paths, where
skew should be matched to within ±10ps.
4.
Signal trace impedance should not vary more than
±5%. If in doubt, perform TDR analysis of all high-speed
signal traces.
5.
Maintain compact filter networks as close to filter pins
as possible. Provide ground plane relief under filter path
to reduce stray capacitance. Be careful of crosstalk
coupling into the filter network.
6.
Maintain low jitter on the REFCLK input. Isolate the
XTAL oscillator from power supply noise by adequately
decoupling. Keep XTAL oscillator close to device, and
minimize capacitive coupling from adjacent signals.
7.
Higher speed operation may require use of
fundamental-tone (third-overtone typically has more
jitter) crystal-based oscillator for optimum performance.
Evaluate and compare candidates by measuring
TXCLK jitter.
8.
All unused outputs require termination. To conserve
power, unused PECL outputs can be terminated with a
1k resistor to VEE.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3456W16S-8PY | CONN PLUG 5POS STRAIGHT W/PINS |
| VE-B3L-MW-B1 | CONVERTER MOD DC/DC 28V 100W |
| MS3456W16S-8PX | CONN PLUG 5POS STRAIGHT W/PINS |
| MS3456W16S-8P | CONN PLUG 5POS STRAIGHT W/PINS |
| VE-B3L-MV | CONVERTER MOD DC/DC 28V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP7940MT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low-Cost I2Ca?￠ Real-Time Clock/Calendar with SRAM |
| MCP7940MT-I/MNY | 功能描述:實時時鐘 I2C RTCC 64B SRAM No VBAT RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MCP7940MT-I/MS | 功能描述:實時時鐘 I2C RTCC 64B SRAM No VBAT RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MCP7940MT-I/SN | 功能描述:實時時鐘 I2C RTCC 64B SRAM No VBAT RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| MCP7940MT-I/ST | 功能描述:實時時鐘 I2C RTCC 64B SRAM No VBAT RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。