參數資料
型號： MCP6023-I/SN
廠商： Microchip Technology
文件頁數： 9/42頁
文件大小： 0K
描述： IC OPAMP 2.5V R-R I/O 8SOIC
標準包裝： 100
放大器類型： 通用
電路數： 1
輸出類型： 滿擺幅
轉換速率： 7 V/µs
增益帶寬積： 10MHz
電流 - 輸入偏壓： 1pA
電壓 - 輸入偏移： 500µV
電流 - 電源： 1mA
電流 - 輸出 / 通道： 30mA
電壓 - 電源，單路/雙路(±)： 2.5 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOICN
包裝： 管件
產品目錄頁面： 679 (CN2011-ZH PDF)
其它名稱： MCP6023I/SN
2009 Microchip Technology Inc.
DS21685D-page 17
MCP6021/1R/2/3/4
4.0
APPLICATIONS INFORMATION
The MCP6021/1R/2/3/4 family of operational amplifiers
are fabricated on Microchip’s state-of-the-art CMOS
process. They are unity-gain stable and suitable for a
wide range of general-purpose applications.
4.1
Rail-to-Rail Input
4.1.1
PHASE REVERSAL
The MCP6021/1R/2/3/4 op amp is designed to prevent
phase reversal when the input pins exceed the supply
voltages. Figure 2-42 shows the input voltage exceed-
ing the supply voltage without any phase reversal.
4.1.2
INPUT VOLTAGE AND CURRENT
LIMITS
The ESD protection on the inputs can be depicted as
shown in Figure 4-1. This structure was chosen to
protect the input transistors, and to minimize input bias
current (IB). The input ESD diodes clamp the inputs
when they try to go more than one diode drop below
VSS. They also clamp any voltages that go too far
above VDD; their breakdown voltage is high enough to
allow normal operation, and low enough to bypass
quick ESD events within the specified limits.
FIGURE 4-1:
Simplified Analog Input ESD
Structures.
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
currents and voltages at the VIN+ and VIN– pins (see
Absolute Maximum Ratings at the beginning of
shows the recommended approach to protecting these
inputs. The internal ESD diodes prevent the input pins
(VIN+ and VIN–) from going too far below ground, and
the resistors R1 and R2 limit the possible current drawn
out of the input pins. Diodes D1 and D2 prevent the
input pins (VIN+ and VIN–) from going too far above
VDD, and dump any currents onto VDD. When
implemented as shown, resistors R1 and R2 also limit
the current through D1 and D2.
FIGURE 4-2:
Protecting the Analog
Inputs.
It is also possible to connect the diodes to the left of
resistors R1 and R2. In this case, current through the
diodes D1 and D2 needs to be limited by some other
mechanism. The resistors then serve as in-rush current
limiters; the DC current into the input pins (VIN+ and
VIN–) should be very small.
A significant amount of current can flow out of the
inputs when the common mode voltage (VCM) is below
ground (VSS); see Figure 2-42. Applications that are
high impedance may need to limit the useable voltage
range.
4.1.3
NORMAL OPERATION
The input stage of the MCP6021/1R/2/3/4 op amps use
two differential CMOS input stages in parallel. One
operates at low common mode input voltage (VCM),
while the other operates at high VCM. WIth this topol-
ogy, the device operates with Vcm up to 0.3V above
VDD and 0.3V below VSS.
4.2
Rail-to-Rail Output
The Maximum Output Voltage Swing is the maximum
swing
possible
under
a
particular
output
load.
According to the specification table, the output can
reach within 20 mV of either supply rail when
RL =10kΩ. See Figure 2-31 and Figure 2-34 for more
information concerning typical performance.
4.3
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases, and the closed loop bandwidth is
reduced. This produces gain-peaking in the frequency
response, with overshoot and ringing in the step
response.
Bond
Pad
Bond
Pad
Bond
Pad
VDD
VIN+
VSS
Input
Stage
Bond
Pad
VIN–
V1
MCP602X
R1
VDD
D1
R1 >
VSS – (minimum expected V1)
2mA
R2 >
VSS – (minimum expected V2)
2mA
V2
R2
D2
R3
相關PDF資料
PDF描述
RW1S0BAR360JET RES POWER .360 OHM 1W 5% SMT
SSQ-148-02-S-S CONN RCPT .100" 48POS SNGL GOLD
LT1490AIDD#PBF IC OP AMP R-R IN/OUT DUAL 8-DFN
SSQ-149-02-S-S CONN RCPT .100" 49POS SNGL GOLD
SSQ-101-02-G-S-RA CONN RCPT .100" 1POS R/A SGL AU
相關代理商/技術參數
參數描述
MCP6023T 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6023T-E/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6023T-E/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6023T-E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
MCP6023T-E/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Rail-to-Rail Input/Output, 10 MHz Op Amps
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*