- 您現在的位置：買賣IC網 > PDF目錄9344 > MCP4232-104E/MF (Microchip Technology)IC POT DGTL DUAL 100K RHEO 10DFN PDF資料下載
參數資料
| 型號： | MCP4232-104E/MF |
| 廠商： | Microchip Technology |
| 文件頁數： | 21/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL DUAL 100K RHEO 10DFN |
| 標準包裝： | 120 |
| 接片： | 129 |
| 電阻（歐姆）： | 100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 150 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-DFN-EP（3x3） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
28
M9999-070910-1.0
RMII Back-to-Back Mode (KSZ8051RNL only)
In RMII Back-to-Back mode, a KSZ8051RNL interfaces with another KSZ8051RNL, or a KSZ8041FTL to provide a
complete 100Mbps copper repeater, or media converter solution, respectively.
The KSZ8051RNL devices are configured to RMII Back-to-Back mode after power-up or reset with the following:
Strapping pin CONFIG[2:0] (pins 18, 29, 28) set to ‘101’
A common 50MHz reference clock connected to XI (pin 9)
RMII signals connected as shown in the following table.
KSZ8051RNL (100Base-TX copper)
[Device 1]
KSZ8051RNL (100Base-TX copper)
[Device 2]
Pin Name
Pin Number
Pin Type
Pin Name
Pin Number
Pin Type
CRSDV
18
Output
TXEN
23
Input
RXD1
15
Output
TXD1
25
Input
RXD0
16
Output
TXD0
24
Input
TXEN
23
Input
CRSDV
18
Output
TXD1
25
Input
RXD1
15
Output
TXD0
24
Input
RXD0
16
Output
Table 4. RMII Signal Connection for RMII Back-to-Back Mode (100Base-TX Copper Repeater)
MII Management (MIIM) Interface
The KSZ8051MNL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state
of the KSZ8051MNL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the
PHY settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows the external controller
to communicate with one or more PHY devices.
A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE
802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section
for details.
As the default, the KSZ8051MNL/RNL supports unique PHY addresses 1 to 7, and broadcast PHY address 0. The latter is
defined per the IEEE 802.3 Specification, and can be used to read/write to a single KSZ8051MNL/RNL device, or write to
multiple KSZ8051MNL/RNL devices simultaneously.
Optionally, PHY address 0 can be disabled as the broadcast address by either hardware pin strapping (B-CAST_OFF, pin
19) or software (register 16h, bit 9), and assigned as a unique PHY address.
The PHYAD[2:0] strapping pins are used to assigned a unique PHY address between 0 and 7 to each KSZ8051MNL/RNL
device.
The following table shows the MII Management frame format for the KSZ8051MNL/RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 5. MII Management Frame Format – for KSZ8051MNL/RNL
相關PDF資料 |
PDF描述 |
|---|---|
| M83723/86W14156 | CONN PLUG 15POS STRAIGHT W/SCKT |
| VE-B3N-IU-F1 | CONVERTER MOD DC/DC 18.5V 200W |
| VI-26T-MW | CONVERTER MOD DC/DC 6.5V 100W |
| X1205S8Z | IC RTC/CALENDAR/ALARM 4K 8-SOIC |
| MCP4232-502E/MF | IC POT DGTL DUAL 5K RHEO 10DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP4232-502E/MF | 功能描述:數字電位計 IC Dual 7B V SPI Rheo RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MCP4232-502E/UN | 功能描述:數字電位計 IC Dual 7B V SPI Rheo RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MCP4232-502-E/UN | 功能描述:數字電位計 IC Dual, 7bit, V, SPI, Rheo RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MCP4232-502E/UN | 制造商:Microchip Technology Inc 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE 制造商:Microchip Technology Inc 功能描述:IC, DIG POT, 5 kohm, 129 STEPS, Dual, MSOP |
| MCP4232-503E/MF | 功能描述:數字電位計 IC Dual 7B V SPI Rheo RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。