- 您現在的位置：買賣IC網 > PDF目錄9345 > MCP4152-104E/MF (Microchip Technology)IC POT DGTL SNGL 100K RHEO 8DFN PDF資料下載
參數資料
| 型號： | MCP4152-104E/MF |
| 廠商： | Microchip Technology |
| 文件頁數： | 26/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL SNGL 100K RHEO 8DFN |
| 標準包裝： | 120 |
| 接片： | 257 |
| 電阻（歐姆）： | 100k |
| 電路數： | 1 |
| 溫度系數： | 標準值 150 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN-EP（3x3） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
32
M9999-070910-1.0
NAND Tree I/O Testing
The following procedure can be used to check for faults on the KSZ8051MNL/RNL digital I/O pin connections to the
board:
1. Enable NAND tree mode by either hardware pin strapping (NAND_Tree#, pin 21) or software (register 16h, bit 5).
2. Use board logic to drive all KSZ8051MNL/RNL NAND tree input pins high.
3. Use board logic to drive each NAND tree input pin, per KSZ8051MNL/RNL NAND Tree pin order, as follow:
a. Toggle the first pin (MDIO) from high to low, and verify the CRS/CONFIG1 pin switch from low to high to
indicate that the first pin is connected properly.
b. Leave the first pin (MDIO) low.
c. Toggle the second pin (MDC) from high to low, and verify the CRS/CONFIG1 pin switch from high to low
to indicate that the second pin is connected properly.
d. Leave the first pin (MDIO) and the second pin (MDC) low.
e. Toggle the third pin from high to low, and verify the CRS/CONFIG1 pin switch from low to high to indicate
that the third pin is connected properly.
f.
Continue with this sequence until all KSZ8051MNL/RNL NAND tree input pins have been toggled.
Each KSZ8051MNL/RNL NAND tree input pin must cause the CRS/CONFIG1 output pin to toggle high-to-low or low-to-
high to indicate a good connection. If the CRS/CONFIG1 pin fails to toggle when the KSZ8051MNL/RNL input pin toggles
from high to low, the input pin has a fault.
Power Management
The KSZ8051MNL/RNL offers the following power management modes:
Power Saving Mode
Power Saving Mode is used to reduce the transceiver power consumption when the cable is unplugged. It is enabled by
writing a one to register 1Fh, bit 10, and is in effect when auto-negotiation mode is enabled and cable is disconnected (no
link).
In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter, energy detect and PLL
circuits.
By default, Power Saving Mode is disabled after power-up.
Energy Detect Power Down Mode
Energy Detect Power Down Mode is used to further reduce the transceiver power consumption when the cable is un-
plugged. It is enabled by writing a zero to register 18h, bit 11, and is in effect when auto-negotiation mode is enabled and
cable is disconnected (no link).
In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter and energy detect circuits.
Further power consumption is achieved by extending the time interval in between transmissions of link pulses to check for
the presence of a link partner. The periodic transmission of link pulses is needed to ensure two link partners in the same
low power state and with auto MDI/MDI-X disabled can wake up when the cable is connected between them.
By default, Energy Detect Power Down Mode is disabled after power-up.
Power Down Mode
Power Down Mode is used to power down the KSZ8051MNL/RNL device when it is not in use after power-up. It is
enabled by writing a one to register 0h, bit 11.
In this mode, the KSZ8051MNL/RNL disables all internal functions, except for the MII management interface. The
KSZ8051MNL/RNL exits (disables) Power Down Mode after register 0h, bit 11 is set back to zero.
Slow Oscillator Mode
Slow Oscillator Mode is used to disconnect the input reference crystal/clock on XI (pin 9) and select the on-chip slow
oscillator when the KSZ8051MNL/RNL device is not in use after power-up. It is enabled by writing a one to register 11h,
bit 5.
Slow Oscillator Mode works in conjunction with Power Down Mode to put the KSZ8051MNL/RNL device in the lowest
相關PDF資料 |
PDF描述 |
|---|---|
| MCP4151-104E/MF | IC POT DGTL SNGL 100K SPI 8DFN |
| MCP4152-104E/MS | IC POT DGTL SNGL 100K RHEO 8MSOP |
| MCP4152-503E/MS | IC POT DGTL SNGL 50K RHEO 8MSOP |
| VE-2NT-MY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-2NT-MY-F3 | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP4152-104I/MF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory |
| MCP4152-104I/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory |
| MCP4152-104I/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory |
| MCP4152-104I/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory |
| MCP4152-104I/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory |
發布緊急采購，3分鐘左右您將得到回復。