參數資料
型號： MCP4131T-103E/MF
廠商： Microchip Technology
文件頁數： 22/59頁
文件大?。?/td> 0K
描述： IC POT DGTL SNGL 10K SPI 8DFN
標準包裝： 3,300
接片： 129
電阻（歐姆）： 10k
電路數： 1
溫度系數： 標準值 150 ppm/°C
存儲器類型： 易失
接口： 3 線 SPI（芯片選擇）
電源電壓： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-VDFN 裸露焊盤
供應商設備封裝： 8-DFN-EP（3x3）
包裝： 帶卷 (TR)
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
29
M9999-070910-1.0
Interrupt (INTRP)
INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status
update to the KSZ8051MNL/RNL PHY register. Register 1Bh, bits [15:8] are the interrupt control bits to enable and
disable the conditions for asserting the INTRP signal. Register 1Bh, bits [7:0] are the interrupt status bits to indicate which
interrupt conditions have occurred. The interrupt status bits are cleared after reading register 1Bh.
Register 1Fh, bit 9 sets the interrupt level to active high or active low. The default is active low.
The MII management bus option gives the MAC processor complete access to the KSZ8051MNL/RNL control and status
registers. Additionally, an interrupt pin eliminates the need for the processor to poll the PHY for status change.
HP Auto MDI/MDI-X
HP Auto MDI/MDI-X configuration eliminates the confusion of whether to use a straight cable or a crossover cable
between the KSZ8051MNL/RNL and its link partner. This feature allows the KSZ8051MNL/RNL to use either type of cable
to connect with a link partner that is in either MDI or MDI-X mode. The auto-sense function detects transmit and receive
pairs from the link partner, and then assigns transmit and receive pairs of the KSZ8051MNL/RNL accordingly.
HP Auto MDI/MDI-X is enabled by default. It is disabled by writing a one to register 1Fh, bit 13. MDI and MDI-X mode is
selected by register 1Fh, bit 14 if HP Auto MDI/MDI-X is disabled.
An isolation transformer with symmetrical transmit and receive data paths is recommended to support auto MDI/MDI-X.
The IEEE 802.3 Standard defines MDI and MDI-X as follows:
MDI
MDI-X
RJ-45 Pin
Signal
RJ-45 Pin
Signal
1
TX+
1
RX+
2
TX-
2
RX-
3
RX+
3
TX+
6
RX-
6
TX-
Table 6. MDI/MDI-X Pin Definition
Straight Cable
A straight cable connects a MDI device to a MDI-X device, or a MDI-X device to a MDI device. The following figure depicts
a typical straight cable connection between a NIC card (MDI) and a switch, or hub (MDI-X).
Figure 6. Typical Straight Cable Connection
相關PDF資料
PDF描述
DS17885EN-3+ IC RTC 3V 8K NV RAM 28TSOP
MCP4131T-104E/MF IC POT DGTL SNGL 100K SPI 8DFN
VE-260-MW CONVERTER MOD DC/DC 5V 100W
VE-B6V-IU-S CONVERTER MOD DC/DC 5.8V 200W
DS1687-3+C01 IC RTC 3V 64-BIT Y2K 24-EDIP
相關代理商/技術參數
參數描述
MCP4131T-103I/MF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory
MCP4131T-103I/ML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory
MCP4131T-103I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory
MCP4131T-103I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory
MCP4131T-103I/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Volatile Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*