參數資料
型號： MCP3201T-CI/ST
廠商： Microchip Technology
文件頁數： 15/40頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 2.7V 1CH SPI 8TSSOP
標準包裝： 2,500
位數： 12
采樣率（每秒）： 100k
數據接口： 串行，SPI?
轉換器數目： 1
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 8-TSSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個單端，單極
其它名稱： MCP3201T-CI/ST -ND
MCP3201
DS21290F-page 22
1998-2011 Microchip Technology Inc.
6.2
Maintaining Minimum Clock Speed
When the MCP3201 initiates the sample period, charge
is stored on the sample capacitor. When the sample
period is complete, the device converts one bit for each
clock that is received. It is important for the user to note
that a slow clock rate will allow charge to bleed off the
sample cap while the conversion is taking place. At
85°C (worst-case condition), the part will maintain
proper charge on the sample capacitor for at least
1.2 ms after the sample period has ended. This means
that the time between the end of the sample period and
the time that all 12 data bits have been clocked out
must not exceed 1.2 ms (effective clock frequency of
10 kHz). Failure to meet this criteria may induce
linearity errors into the conversion outside the rated
specifications. It should be noted that during the entire
conversion cycle, the A/D Converter does not require a
constant clock speed or duty cycle, as long as all timing
specifications are met.
6.3
Buffering/Filtering the Analog
Inputs
If the signal source for the A/D Converter is not a low-
impedance source, it will have to be buffered
or inaccurate
conversion
results
may
occur.
See Figure 4-2. It is also recommended that a filter be
used to eliminate any signals that may be aliased back
into the conversion results. This is illustrated in
Figure 6-3 where an op amp is used to drive the analog
input of the MCP3201 device. This amplifier provides a
low-impedance source for the converter input and a
low-pass filter, which eliminates unwanted high-
frequency noise.
Low-pass (anti-aliasing) filters can be designed using
Microchip’s interactive FilterLab software. FilterLab
will calculate capacitor and resistor values, as well as
determine the number of poles that are required for the
application. For more information on filtering signals,
see application note AN699 “Anti-Aliasing Analog
Filters for Data Acquisition Systems.”
FIGURE 6-3:
The MCP601 Operational
Amplifier is used to implement a 2nd order anti-
aliasing filter for the signal being converted by
the MCP3201 device.
MCP3201
VDD
10 F
IN-
IN+
-
+
VIN
C1
C2
VREF
4.096V
Reference
1F
10 F
0.1 F
MCP601
R1
R2
R3
R4
MCP1541
CL
相關PDF資料
PDF描述
VI-B4F-IV-F3 CONVERTER MOD DC/DC 72V 150W
VE-BVP-MX-F4 CONVERTER MOD DC/DC 13.8V 75W
VI-B4F-IV-F2 CONVERTER MOD DC/DC 72V 150W
VE-BVN-MX-F2 CONVERTER MOD DC/DC 18.5V 75W
VI-B4D-IV-F4 CONVERTER MOD DC/DC 85V 150W
相關代理商/技術參數
參數描述
MCP3201T-I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface
MCP3201T-I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface
MCP3201T-I/SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface
MCP3201T-I/ST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface
MCP3202 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V Dual Channel 12-Bit A/D Converter with SPI Serial Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*