- 您現在的位置：買賣IC網 > PDF目錄10738 > MCP3021A0T-E/OT (Microchip Technology)ADC 10BIT I2C INTERFACE SOT23-5 PDF資料下載
參數資料
| 型號： | MCP3021A0T-E/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 8/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | ADC 10BIT I2C INTERFACE SOT23-5 |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 22.3k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 1 個單端，單極 |
| 其它名稱： | MCP3021A0T-E/OTDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
MCP3021
DS21805A-page 16
2003 Microchip Technology Inc.
5.2
Device Addressing
The address byte is the first byte received following the
START condition from the master device. The first part
of the control byte consists of a 4-bit device code,
which is set to 1001 for the MCP3021. The device code
is followed by three address bits: A2, A1 and A0. The
default address bits are 101 (contact the Microchip fac-
tory for additional address bit options).The address bits
allow up to eight MCP3021 devices on the same bus
and are used to determine which device is accessed.
The eighth bit of the slave address determines if the
master device wants to read conversion data or write to
the MCP3021. When set to a ‘1’, a read operation is
selected. When set to a ‘0’, a write operation is
selected. There are no writable registers on the
MCP3021, therefore, this bit must be set to a ’1’ to
initiate a conversion.
The MCP3021 is a slave device that is compatible with
the 2-wire I2C serial interface protocol. A hardware
connection diagram is shown in Figure 6-2. Communi-
cation is initiated by the microcontroller (master
device), which sends a START bit followed by the
address byte.
On completion of the conversion(s) performed by the
MCP3021, the microcontroller must send a STOP bit to
stop the communication.
The last bit in the device address byte is the R/W bit.
When this bit is a logic ‘1’, a conversion will be exe-
cuted. Setting this bit to logic ‘0’ will also result in an
“acknowledge” (ACK) from the MCP3021, with the
device then releasing the bus. This can be used for
device polling (refer to Section 6.3, “Device Polling”).
FIGURE 5-2:
Device Addressing.
5.3
Executing a Conversion
This section will describe the details of communicating
with the MCP3021 device. Initiating the sample and
hold acquisition, reading the conversion data and
executing multiple conversions will be discussed.
5.3.1
INITIATING THE SAMPLE AND
HOLD
The acquisition and conversion of the input signal
begins with the falling edge of the R/W bit of the
address byte. At this point, the internal clock initiates
the sample, hold and conversion cycle, all of which are
internal to the ADC.
FIGURE 5-3:
Initiating the Conversion,
Address Byte.
FIGURE 5-4:
Initiating the Conversion,
Continuous Conversions.
START
READ/WRITE
SLAVE ADDRESS
R/W
A
1
0
1
0
1
Address Bits1
1 Contact Microchip for additional address bits.
Device Code
1234
56
7
8
9
SCL
SDA
1
0
1 A2 A1 A0 R/W
AC
K
Start
Bit
Address Byte
Address bits
Device bits
tACQ + tCONV is
initiated here
SCL
SDA
D1 D0 X
AC
K
Lower Data Byte (n)
tACQ + tCONV is
initiated here
D4 D3 D2
X
D5
AC
K
D6
17 18 19 20 21 22 23 24 25 26
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WY-MY-B1 | CONVERTER MOD DC/DC 3.3V 33W |
| VI-2WY-MW-B1 | CONVERTER MOD DC/DC 3.3V 66W |
| VI-2WW-MY-B1 | CONVERTER MOD DC/DC 5.5V 50W |
| MCP3021A5T-E/OT | IC ADC 10BIT 2.7V 1CH SOT23A-5 |
| VI-2W0-MY-B1 | CONVERTER MOD DC/DC 5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3021A1T-E/OT | 功能描述:模數轉換器 - ADC 10-bit ADC I2C Single Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3021A2T-E/OT | 功能描述:模數轉換器 - ADC 10-bit ADC I2C Single Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3021A3T-E/OT | 功能描述:模數轉換器 - ADC 10-bit ADC I2C Single Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3021A4T-E/OT | 功能描述:模數轉換器 - ADC 10-bit ADC I2C Single Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3021A5T-E/OT | 功能描述:模數轉換器 - ADC 10-bit I2C Sgl Chnl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。