參數資料
型號： MCP2551-E/P
廠商： Microchip Technology
文件頁數： 20/24頁
文件大小： 0K
描述： IC TRANSCEIVER CAN HI-SPD 8-DIP
標準包裝： 60
類型： 收發器
驅動器/接收器數： 1/1
規程： CAN
電源電壓： 4.5 V ~ 5.5 V
安裝類型： 通孔
封裝/外殼： 8-DIP（0.300"，7.62mm）
供應商設備封裝： 8-PDIP
包裝： 管件
配用： AC164130-2-ND - DAUGHTER BOARD CAN/LIN PICTAIL
MCP2515DM-BM-ND - BOARD DEMO FOR MCP2515/51
MCP2515DM-PTPLS-ND - BOARD DAUGHTER PICTAIL MCP2515
AC164130-ND - BOARD DAUGHT PICTL PLUS ECAN/LIN
2010 Microchip Technology Inc.
DS21667F-page 5
MCP2551
1.5
TXD Permanent Dominant
Detection
If the MCP2551 detects an extended Low state on the
TXD input, it will disable the CANH and CANL output
drivers in order to prevent the corruption of data on the
CAN bus. The drivers are disabled if TXD is Low for
more
than
1.25 ms
(minimum).
This
implies
a
maximum bit time of 62.5 s (16 kb/s bus rate),
allowing up to 20 consecutive transmitted Dominant
bits during a multiple bit error and error frame scenario.
The drivers remain disabled as long as TXD remains
Low. A rising edge on TXD will reset the timer logic and
enable the CANH and CANL output drivers.
1.6
Power-on Reset
When the device is powered on, CANH and CANL
remain in a high-impedance state until VDD reaches the
voltage-level VPORH. In addition, CANH and CANL will
remain in a high-impedance state if TXD is Low when
VDD reaches VPORH. CANH and CANL will become
active only after TXD is asserted High. Once powered
on, CANH and CANL will enter a high-impedance state
if the voltage level at VDD falls below VPORL, providing
voltage brown-out protection during normal operation.
1.7
Pin Descriptions
The 8-pin pinout is listed in Table 1-3.
TABLE 1-3:
MCP2551 PINOUT
1.7.1
TRANSMITTER DATA INPUT (TXD)
TXD is a TTL-compatible input pin. The data on this pin
is driven out on the CANH and CANL differential output
pins. It is usually connected to the transmitter data
output of the CAN controller device. When TXD is Low,
CANH and CANL are in the Dominant state. When TXD
is High, CANH and CANL are in the Recessive state,
provided that another CAN node is not driving the CAN
bus with a Dominant state. TXD has an internal pull-up
resistor (nominal 25 k
Ω to VDD).
1.7.2
GROUND SUPPLY (VSS)
Ground supply pin.
1.7.3
SUPPLY VOLTAGE (VDD)
Positive supply voltage pin.
1.7.4
RECEIVER DATA OUTPUT (RXD)
RXD is a CMOS-compatible output that drives High or
Low depending on the differential signals on the CANH
and CANL pins and is usually connected to the receiver
data input of the CAN controller device. RXD is High
when the CAN bus is Recessive and Low in the
Dominant state.
1.7.5
REFERENCE VOLTAGE (VREF)
Reference Voltage Output (defined as VDD/2).
1.7.6
CAN LOW (CANL)
The CANL output drives the Low side of the CAN
differential bus. This pin is also tied internally to the
receive input comparator.
1.7.7
CAN HIGH (CANH)
The CANH output drives the high-side of the CAN
differential bus. This pin is also tied internally to the
receive input comparator.
1.7.8
SLOPE RESISTOR INPUT (RS)
The RS pin is used to select High-Speed, Slope-Control
or Standby modes via an external biasing resistor.
Pin
Number
Pin
Name
Pin Function
1
TXD
Transmit Data Input
2VSS
Ground
3VDD
Supply Voltage
4
RXD
Receive Data Output
5VREF
Reference Output Voltage
6
CANL
CAN Low-Level Voltage I/O
7
CANH
CAN High-Level Voltage I/O
8RS
Slope-Control Input
相關PDF資料
PDF描述
VI-J5F-MY-B1 CONVERTER MOD DC/DC 72V 50W
VI-J5W-MW-F1 CONVERTER MOD DC/DC 5.5V 100W
VI-J5V-MW-F4 CONVERTER MOD DC/DC 5.8V 100W
MS27466T11F35PB CONN RCPT 13POS WALL MNT W/PINS
MS27508E12F4P CONN RCPT 4POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
MCP2551I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551-I/P 功能描述:網絡控制器與處理器 IC Hi Spd CAN Transceiv RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2551-I/P 制造商:Microchip Technology Inc 功能描述:Transceiver IC Package/Case:8-DIP
MCP2551I/SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Speed CAN Transceiver
MCP2551-I/SN 功能描述:網絡控制器與處理器 IC Hi Spd CAN Transceiv RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*