- 您現在的位置：買賣IC網 > PDF目錄11582 > MCP2515T-E/SO (Microchip Technology)IC CAN CONTROLLER W/SPI 18SOIC PDF資料下載
參數資料
| 型號： | MCP2515T-E/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 56/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CAN CONTROLLER W/SPI 18SOIC |
| 標準包裝： | 1,100 |
| 控制器類型： | CAN 接口 |
| 接口： | SPI 串行 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 18-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 18-SOIC |
| 包裝： | 帶卷 (TR) |
| 配用： | MCP2515DM-BM-ND - BOARD DEMO FOR MCP2515/51 MCP2515DM-PTPLS-ND - BOARD DAUGHTER PICTAIL MCP2515 MCP2515DM-PCTL-ND - BOARD DEMO FOR MCP2515 DV251001-ND - KIT DEVELOPMENT CAN MCP2510 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
MCP2515
DS21801F-page 6
2010 Microchip Technology Inc.
1.5
CAN Protocol Engine
The CAN protocol engine combines several functional
blocks, shown in Figure 1-4 and described below.
1.5.1
PROTOCOL FINITE STATE
MACHINE
The heart of the engine is the Finite State Machine
(FSM). The FSM is a sequencer that controls the
sequential data stream between the TX/RX shift
register, the CRC register and the bus line. The FSM
also controls the Error Management Logic (EML) and
the parallel data stream between the TX/RX shift
registers and the buffers. The FSM ensures that the
processes of reception, arbitration, transmission and
error-signaling are performed according to the CAN
protocol. The automatic retransmission of messages
on the bus line is also handled by the FSM.
1.5.2
CYCLIC REDUNDANCY CHECK
The Cyclic Redundancy Check register generates the
Cyclic Redundancy Check (CRC) code, which is
transmitted after either the Control Field (for messages
with 0 data bytes) or the Data Field and is used to
check the CRC field of incoming messages.
1.5.3
ERROR MANAGEMENT LOGIC
The Error Management Logic (EML) is responsible for
the fault confinement of the CAN device. Its two
counters, the Receive Error Counter (REC) and the
Transmit Error Counter (TEC), are incremented and
decremented by commands from the bit stream
processor. Based on the values of the error counters,
the CAN controller is set into the states error-active,
error-passive or bus-off.
1.5.4
BIT TIMING LOGIC
The Bit Timing Logic (BTL) monitors the bus line input
and handles the bus-related bit timing according to the
CAN protocol. The BTL synchronizes on a recessive-
to-dominant bus transition at Start-of-Frame (hard
synchronization) and on any further recessive-to-
dominant bus line transition if the CAN controller itself
does not transmit a dominant bit (resynchronization).
The BTL also provides programmable time segments
to compensate for the propagation delay time, phase
shifts and to define the position of the sample point
within the bit time. The programming of the BTL
depends on the baud rate and external physical delay
times.
FIGURE 1-4:
CAN PROTOCOL ENGINE BLOCK DIAGRAM
Bit Timing Logic
CRC<14:0>
Comparator
Receive<7:0>
Transmit<7:0>
Sample<2:0>
Majority
Decision
StuffReg<5:0>
Comparator
Transmit Logic
Receive
Error Counter
Transmit
Error Counter
Protocol
FSM
RX
SAM
BusMon
Rec/Trm Addr.
RecData<7:0>
TrmData<7:0>
Shift<14:0>
(Transmit<5:0>, Receive<7:0>)
TX
REC
TEC
ErrPas
BusOff
Interface to Standard Buffer
SOF
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2140T-I/SO | IC IRDA CONTROLLR DTE/DCE 18SOIC |
| VI-JNH-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| VI-JNF-IW-F1 | CONVERTER MOD DC/DC 72V 100W |
| MCP2140A-I/SO | IC IRDA CONTROLLR DTE/DCE 18SOIC |
| V150A15C400BL | CONVERTER MOD DC/DC 15V 400W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2515T-I/M | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2515T-I/ML | 功能描述:網絡控制器與處理器 IC CAN controller with SPI interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2515T-I/SO | 功能描述:網絡控制器與處理器 IC W/ SPI Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2515T-I/SO-CUT TAPE | 制造商:Microchip 功能描述:MCP2515 Series 5.5 V 1 Mb/s Stand Alone SPI Interface CAN Controller- SOIC-18 |
| MCP2515T-I/ST | 功能描述:網絡控制器與處理器 IC W/ SPI Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。