- 您現在的位置：買賣IC網 > PDF目錄3771 > MCP25020T-I/SL (Microchip Technology)IC I/O EXPANDER CAN 8B 14SOIC PDF資料下載
參數資料
| 型號： | MCP25020T-I/SL |
| 廠商： | Microchip Technology |
| 文件頁數： | 36/66頁 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER CAN 8B 14SOIC |
| 標準包裝： | 2,600 |
| 接口： | CAN |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 無 |
| 頻率 - 時鐘： | 4MHz |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
| 包括： | 存儲器，PWM |
| 配用： | MCP2515DM-PCTL-ND - BOARD DEMO FOR MCP2515 |
| 其它名稱： | MCP25020TI/SL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
2007 Microchip Technology Inc.
DS21664D-page 41
MCP2502X/5X
7.0
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
7.1
Description
The Analog-to-Digital (A/D) module is a four-channel,
10-bit successive approximation type of A/D. The A/D
allows conversion of an analog input signal to a
corresponding 10-bit number. The four channels are
multiplexed on the GP[3:0] pins. The converter is
turned off/on via the ADCON0 register and each
channel is individually enabled via the ADCON1 control
register. The VREF+ and VREF- sources are user-
selectable as internal or external. Each channel can be
set to one of two conversion modes:
1.
Auto-conversion
2.
Convert-on-request.
7.2
A/D Module Registers
The A/D module itself has several registers. The
registers are:
A/D Control Register 0 (ADCON0)
A/D Control Register 1 (ADCON1)
Transmit-on-Change Register (IOINTEN)
Compare and Polarity Register (ADCMPnL)
A/D Result Registers (ADRESnL, ADRESnH)
The ADCON0 register controls the operation of the
A/D module, including auto-conversion rate and enable
bit. The ADCON1 register enables the A/D function on
port pins GP3:GP0, A/D conversion rate and selects
the voltage reference source. The IOINTEN register’s
four least significant bits enable/disable the transmit-
on-change function. The ADCMPnL.ADPOL bit sets
the polarity (above or below threshold) for the transmit-
on-change function.
The result of an A/D conversion is made available to
the user within the data field of the Read A/D Registers
output message via the CAN bus. This message can
be directly requested by another CAN node or be
automatically transmitted (TXIDO), as has been
described previously.
Additionally, the individual channel results may be read
using the “Read Register” command as described in
as shown in Table 3-2 by addressing the appropriate
A/D result register (ADRESnL and ADRESnH).
7.3
A/D Conversion Modes
There are two modes of conversion that can be
individually selected for each analog channel that has
been
enabled.
These
are
auto-conversion
and
conversion-on-request.
7.3.1
AUTO-CONVERSION MODE
If the Auto-conversion mode is selected (STCON), an
A/D conversion is performed sequentially for each
channel that has been set to Analog Input mode and
has been configured for Auto-conversion mode.
Conversion starts with AN0 and is immediately
followed by AN1, etc. Once the conversion has
completed, the value is stored in the analog channel
registers for the respective channel.
The rate of the auto-conversion is determined by a
timer and prescaler. The formula for determining
conversion rates is:
Typical conversion rates with a 20 MHz oscillator input
are shown in Table 7-1.
TABLE 7-1:
AUTO-CONVERSION RATES
FOR GIVEN PRESCALE
RATES AT 20 MHZ
The timer is turned on if one of the GPnTXC bits are set
in the IOINTEN register and configured as analog
input.
The prescaler counter is cleared when the device is
reset (RST reset or Power-on reset).
Note:
The GPDDR register controls the direction
of the GPIO pins, even when they are
being used as analog inputs. The user
must ensure that the bits in the GPDDR
register are maintained set (input) when
using them as analog inputs.
TOPS[2:0]
Prescale
Rate
Auto-Conversion
Rate
000
1:1
51 s
001
1:8
410 s
010
1:32
2 ms
011
1:128
7 ms
100
1:512
26 ms
101
1:1024
52 ms
110
1:2048
105 ms
111
1:4096
210 ms
T
OSC
() 1024
() Prescaler rate
()
相關PDF資料 |
PDF描述 |
|---|---|
| ATTINY26L-8SUR | IC MCU AVR 2K 5V 8MHZ 20SOIC |
| ATTINY26-16SUR | IC MCU AVR 2K 16MHZ IND 20SOIC |
| ATTINY28L-4AUR | IC MCU 8BIT 2K FLASH 32TQFP |
| ATMEGA48V-10MMUR | MCU AVR 4KB FLASH 20MHZ 28QFN |
| U65-404-60-P | CONN COVER REAR FOR 4X RCPT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP25025 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O EXPANDER FAMILY |
| MCP25025E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family |
| MCP25025E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family |
| MCP25025I/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family |
| MCP25025-I/P | 功能描述:網絡控制器與處理器 IC Digital 1 Wire capab RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。