參數資料
型號： MCP23S08T-E/SO
廠商： Microchip Technology
文件頁數： 7/44頁
文件大小： 0K
描述： IC I/O EXPANDER SPI 8B 18SOIC
標準包裝： 1,100
接口： SPI
輸入/輸出數： 8
中斷輸出： 是
頻率 - 時鐘： 10MHz
電源電壓： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 18-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 18-SOIC
包裝： 帶卷 (TR)
包括： POR
配用： GPIODM-KPLCD-ND - BOARD DEMO LCD GPIO EXP KEYPAD
2007 Microchip Technology Inc.
DS21919E-page 15
MCP23008/MCP23S08
1.6.6
CONFIGURATION (IOCON)
REGISTER
The IOCON register contains several bits for
configuring the device:
The Sequential Operation (SEQOP) controls the
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer
does not automatically increment after each byte
is clocked during a serial transfer. This feature is
useful when it is desired to continuously poll
(read) or modify (write) a register.
The Slew Rate (DISSLW) bit controls the slew
rate function on the SDA pin. If enabled, the SDA
slew rate will be controlled when driving from a
high to a low.
The Hardware Address Enable (HAEN) control bit
enables/disables the hardware address pins (A1,
A0) on the MCP23S08. This bit is not used on the
MCP23008. The address pins are always enabled
on the MCP23008.
The Open-Drain (ODR) control bit enables/
disables the INT pin for open-drain configuration.
The Interrupt Polarity (INTPOL) control bit sets
the polarity of the INT pin. This bit is functional
only when the ODR bit is cleared, configuring the
INT pin as active push-pull.
REGISTER 1-6:
IOCON – I/O EXPANDER CONFIGURATION REGISTER (ADDR 0x05)
U-0
R/W-0
U-0
—
SEQOP
DISSLW
HAEN
ODR
INTPOL
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-6
Unimplemented: Read as ‘0’.
bit 5
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
bit 4
DISSLW: Slew Rate control bit for SDA output.
1 = Slew rate disabled.
0 = Slew rate enabled.
bit 3
HAEN: Hardware Address Enable bit (MCP23S08 only).
Address pins are always enabled on MCP23008.
1 = Enables the MCP23S08 address pins.
0 = Disables the MCP23S08 address pins.
bit 2
ODR: This bit configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
bit 1
INTPOL: This bit sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
bit 0
Unimplemented: Read as ‘0’.
相關PDF資料
PDF描述
346-220-058 CARD GUIDE OFFSET
ATTINY44V-10MUR MCU AVR 4KB FLASH 10MHZ 20-QFN
ATTINY44-20MUR MCU AVR 4KB FLASH 20MHZ 20QFN
PCA9670D,518 IC I/O EXPANDER I2C 8B 16SOIC
ATTINY2313V-10SUR IC MCU AVR 2K FLASH 20SOIC
相關代理商/技術參數
參數描述
MCP23S09 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs
MCP23S09-E/MG 功能描述:接口 - 專用 8B I/O Expander SPI interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MCP23S09-E/MG 制造商:Microchip Technology Inc 功能描述:; Bus Frequency:10MHz; IC Interface Type 制造商:Microchip Technology Inc 功能描述:IC, I/O EXPANDER, 8BIT, 10MHZ, QFN-16
MCP23S09-E/P 功能描述:接口-I/O擴展器 8-bit I/O Expander SPI interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MCP23S09-E/P 制造商:Microchip Technology Inc 功能描述:I/O Expander IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*