- 您現在的位置：買賣IC網 > PDF目錄3771 > MCP23S08-E/P (Microchip Technology)IC I/O EXPANDER SPI 8B 18DIP PDF資料下載
參數資料
| 型號： | MCP23S08-E/P |
| 廠商： | Microchip Technology |
| 文件頁數： | 40/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER SPI 8B 18DIP |
| 產品培訓模塊： | GPIO Expanders |
| 標準包裝： | 25 |
| 接口： | SPI |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 10MHz |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 18-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 18-PDIP |
| 包裝： | 管件 |
| 包括： | POR |
| 產品目錄頁面： | 684 (CN2011-ZH PDF) |
| 配用： | GPIODM-KPLCD-ND - BOARD DEMO LCD GPIO EXP KEYPAD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁
2007 Microchip Technology Inc.
DS21919E-page 5
MCP23008/MCP23S08
1.0
DEVICE OVERVIEW
The MCP23X08 device provides 8-bit, general
purpose, parallel I/O expansion for I2C bus or SPI
applications. The two devices differ in the number of
hardware address pins and the serial interface:
MCP23008 – I2C interface; three address pins
MCP23S08 – SPI interface; two address pins
The MCP23X08 consists of multiple 8-bit configuration
registers for input, output and polarity selection. The
system master can enable the I/Os as either inputs or
outputs by writing the I/O configuration bits. The data
for each input or output is kept in the corresponding
Input or Output register. The polarity of the Input Port
register can be inverted with the Polarity Inversion
register. All registers can be read by the system master.
The interrupt output can be configured to activate
under two conditions (mutually exclusive):
1.
When
any
input
state
differs
from
its
corresponding input port register state, this is
used to indicate to the system master that an
input state has changed.
2.
When an input state differs from a preconfigured
register value (DEFVAL register).
The Interrupt Capture register captures port values at
the time of the interrupt, thereby saving the condition
that caused the interrupt.
The Power-on Reset (POR) sets the registers to their
default values and initializes the device state machine.
The hardware address pins are used to determine the
device address.
1.1
Pin Descriptions
TABLE 1-1:
PINOUT DESCRIPTION
Pin
Name
PDIP/
SOIC
QFN
SSOP
Pin
Type
Function
SCL/SCK
1
19
1
I
Serial clock input.
SDA/SI
2
20
2
I/O
Serial data I/O (MCP23008)/Serial data input (MCP23S08).
A2/SO
3
1
3
I/O
Hardware address input (MCP23008)/
Serial data output (MCP23S08).
A2 must be biased externally.
A1
4
2
4
I
Hardware address input. Must be biased externally.
A0
5
3
5
I
Hardware address input. Must be biased externally.
RESET
6
4
6
I
External reset input. Must be biased externally.
NC/CS
7
5
7
I
No connect (MCP23008)/External chip select input (MCP23S08).
INT
8
7
8
O
Interrupt output. Can be configured for active-high, active-low or
open-drain.
VSS
9179
P
Ground.
GP0
10
9
12
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP1
11
10
13
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP2
12
11
14
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP3
13
12
15
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP4
14
13
16
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP5
15
14
17
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP6
16
15
18
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
GP7
17
16
19
I/O
Bidirectional I/O pin. Can be enabled for interrupt-on-change and/or
internal weak pull-up resistor.
VDD
18
20
P
Power.
N/C
—
6, 8
10, 11
—
相關PDF資料 |
PDF描述 |
|---|---|
| MCP23016T-I/SS | IC I/O EXPANDER I2C 16B 28SSOP |
| ATTINY261-15SZ | MCU AVR 2K FLASH 15MHZ 20-SOIC |
| 1761070-1 | CONN PLUG HOUSING HSSDDC2 |
| ATMEGA48-20AUR | IC AVR MCU 4K 20MHZ 32TQFP |
| 788370-4 | CONN GUIDE ASSY MEDIA CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP23S08T-E/ML | 功能描述:接口-I/O擴展器 8bit Input/Output Exp SPI interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S08T-E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Bit I/O Expander with Serial Interface |
| MCP23S08T-E/SO | 功能描述:接口-I/O擴展器 In/Out I2C int RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S08T-E/SS | 功能描述:接口-I/O擴展器 In/Out I2C int RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S09 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
發布緊急采購，3分鐘左右您將得到回復。