- 您現在的位置：買賣IC網 > PDF目錄3771 > MCP23018T-E/SO (Microchip Technology)IC I/O EXPANDER I2C 16B 28SOIC PDF資料下載
參數資料
| 型號： | MCP23018T-E/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 24/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 28SOIC |
| 標準包裝： | 1,600 |
| 接口： | I²C |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 3.4MHz |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MCP23018/MCP23S18
DS22103A-page 30
2008 Microchip Technology Inc.
1.7
Interrupt Logic
If enabled, the MCP23X18 activates the INTn interrupt
output when one of the port pins changes state or when
a pin does not match the pre-configured default. Each
pin is individually configurable as follows:
Enable/disable interrupt via GPINTEN
Can interrupt on either pin change or change from
default as configured in DEFVAL
Both conditions are referred to as Interrupt on Change
(IOC).
The Interrupt Control (INT) Module uses the following
registers/bits:
IOCON.MIRROR - controls if the two interrupt
pins mirror each other.
GPINTEN - Interrupt enable register
INTCON - Controls the source for the IOC
DEFVAL - Contains the register default for IOC
operation
1.7.1
INTA AND INTB
There are two interrupt pins, INTA and INTB. By
default, INTA is associated with GPAn pins (Port A) and
INTB is associated with GPBn pins (Port B). Each port
has an independent signal which is cleared if its
associated GPIO or INTCAP register is read.
1.7.1.1
Mirroring the INT pins
Additionally, the INTn pins can be configured to mirror
each other so that any interrupt will cause both pins to
go active. This is controlled via IOCON.MIRROR.
If IOCON.MIRROR = 0, the internal signals are routed
independently to the INTA and INTB pads.
If IOCON.MIRROR = 1, the internal signals are OR’ed
together and routed to the INTn pads. In this case, the
interrupt will only be cleared if the associated GPIO or
INTCAP is read (see Table 1-6).
TABLE 1-6:
INTERRUPT OPERATION
(IOCON.MIRROR = 1)
1.7.2
IOC FROM PIN CHANGE
If enabled, the MCP23X18 will generate an interrupt if
a mismatch condition exists between the current port
value and the previous port value. Only IOC enabled
pins will be compared. See GPINTEN and INTCON
registers.
1.7.3
IOC FROM REGISTER DEFAULT
If enabled, the MCP23X18 will generate an interrupt if
a mismatch occurs between the DEFVAL register and
the port. Only IOC enabled pins will be compared. See
GPINTEN, INTCON, and DEFVAL registers.
1.7.4
INTERRUPT OPERATION
The INTn interrupt output can be configured as “active
low”, “active high”, or “open drain” via the IOCON
register.
Only those pins that are configured as an input (IODIR
register)
with
interrupt-on-change
(IOC)
enabled
(GPINTEN register) can cause an interrupt. Pins
defined as an output have no effect on the interrupt
output pin.
Input change activity on a port input pin that is enabled
for IOC will generate an internal device interrupt and
the device will capture the value of the port and copy it
into INTCAP.
The first interrupt event will cause the port contents to
be copied into the INTCAP register. Subsequent
interrupt conditions on the port will not cause an
interrupt to occur as long as the interrupt is not cleared
by a read of INTCAP or GPIO.
1.7.5
CLEARING INTERRUPTS
The interrupt will remain active until the INTCAP or
GPIO register is read (depending on IOCON.INTCC).
Writing to these registers will not affect the interrupt.
The interrupt condition will be cleared after the LSb of
the data is clocked out during a Read command of
GPIO or INTCAP (depending on IOCON.INTCC).
Interrupt
Condition
Read Port N*
Interupt
Result
GPIOA
Port A
Clear
Port B
Unchanged
GPIOB
Port A
Unchanged
Port B
Clear
GPIOA and
GPIOB
Port A
Unchanged
Port B
Unchanged
Both Port A
and Port B
Clear
* Port n = GPIOn or INTCAPn
Note:
Assuming IOCON.INTCC = 0 (INT cleared
on GPIO read): The value in INTCAP can
be lost if GPIO is read before INTCAP
while another IOC is pending. After read-
ing GPIO, the interrupt will clear and then
set due to the pending IOC, causing the
INTCAP register to update.
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA48V-10MUR | MCU AVR 4KB FLASH 10MHZ 32QFN |
| MCP23018T-E/MJ | IC I/O EXPANDER I2C 16B 24QFN |
| MCP23017T-E/ML | IC I/O EXPANDER I2C 16B 28QFN |
| 74548-0211 | CONN IPASS SAS 1X1 GUIDE FRAME |
| 8B36-1420 | SHELL 36POS DUAL KEY VERT T-H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP-230-82501-0N | 制造商:Supermicro Computer Inc 功能描述:SUPERMICRO TOP COVER, SC825 - Bulk |
| MCP-230-93301-0N | 制造商:SUPER MICRO COMPUTER, INC. 功能描述:SUPERMICRO 933T-R760 COVER - Bulk |
| MCP23S08 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Bit I/O Expander with Serial Interface |
| MCP23S08-E/ML | 功能描述:接口-I/O擴展器 8bit Input/Output Exp SPI interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23S08-E/P | 功能描述:接口-I/O擴展器 In/Out SPI int RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。