" />
參數資料
型號： MCP23016T-I/SS
廠商： Microchip Technology
文件頁數： 4/38頁
文件大?。?/td> 0K
描述： IC I/O EXPANDER I2C 16B 28SSOP
標準包裝： 2,100
接口： I²C
輸入/輸出數： 16
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 2 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 28-SSOP
包裝： 帶卷 (TR)
包括： POR
MCP23016
DS20090C-page 12
2007 Microchip Technology Inc.
1.8
Serializer/Deserializer
The
Serializer/Deserializer
block
converts
and
transfers data between the I2C bus and GPIO.
1.9
Interrupt Logic
The MCP23016 asserts the open-drain interrupt output
(INT) low when one of the port pins changes state. Only
those pins that are configured as an input can cause an
interrupt. Pins defined as an output have no effect on
INT. The interrupt will remain active until a read from
either the port (GPn) on which the interrupt occurred or
the INTCAPn register is performed. If the input returns
to its previous state before a read operation, it will reset
the interrupt and the INT pin output will tri-state. Each
8-bit port is read separately, so reading GP0 or
INTCAP0 will not clear the interrupt generated by GP1
or INTCAP1, and vice versa.
Input change activity on each port will generate an
interrupt and the value of the particular port will be
captured and copied into INTCAP0/INTCAP1. The
INTCAPn registers are only updated when an interrupt
occurs on INT. These values will stay unchanged until
the user clears the interrupt by reading the port or the
INTCAPn register.
If the input port value changes back to normal before a
user-read, the INT output will be reset. However, the
INTCAP0/INTCAP1 will still contain the value of the
port at the interrupt change. If the port value changes
again, it will re-activate the interrupt and the new value
will be captured.
The first interrupt on change event following an
interrupt RESET will result in a capture event. Any fur-
ther change event that occurs before the interrupt is
reset will not result in a capture event.
1.9.1
INTERRUPT EVENT DETECTION
The IARES bit controls the resolution for detecting an
interrupt-on-change event. If this bit is ‘0’ (default), the
maximum time for detecting a change of event is high,
which results in lower standby current. If this bit is ‘1’, it
takes less time for scanning the activity on the port and
results in higher standby current.
FIGURE 1-2:
READING PORTX AFTER
INTERRUPT EVENT
Port value
PORT X
GPx
INT
is captured
and written to
INTCAPn
Port value
is captured
and written to
INTCAPn
Read GPx
or INTCAPn
相關PDF資料
PDF描述
ATTINY261-15SZ MCU AVR 2K FLASH 15MHZ 20-SOIC
1761070-1 CONN PLUG HOUSING HSSDDC2
ATMEGA48-20AUR IC AVR MCU 4K 20MHZ 32TQFP
788370-4 CONN GUIDE ASSY MEDIA CONVERTER
787663-3 CONN GUIDE ASSY MEDIA CONVERTER
相關代理商/技術參數
參數描述
MCP23017 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Serial Interface
MCP23017-E/ML 功能描述:接口-I/O擴展器 16bit Input/Output Exp I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MCP23017-E/SO 功能描述:接口-I/O擴展器 16bit Input/Output Exp I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MCP23017-E/SO 制造商:Microchip Technology Inc 功能描述:I/O Expander IC
MCP23017-E/SP 功能描述:接口 - 專用 16bit Input/Output Exp I2C interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*