- 您現在的位置：買賣IC網 > PDF目錄11809 > MCP2210-I/SS (Microchip Technology)IC CONVERTER USB-PCI 20-SSOP PDF資料下載
參數資料
| 型號： | MCP2210-I/SS |
| 廠商： | Microchip Technology |
| 文件頁數： | 45/82頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONVERTER USB-PCI 20-SSOP |
| 產品培訓模塊： | MCP2210 Evaluation Kit |
| 標準包裝： | 67 |
| 應用： | 帶 GPIO 的 USB 至 SPI 連接器 |
| 接口： | SPI，USB |
| 電源電壓： | 3.3 V ~ 5.5 V |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
2011 Microchip Technology Inc.
DS22288A-page 5
MCP2210
1.5
USB Transceiver
The MCP2210 has a built-in, USB 2.0, full-speed
transceiver internally connected to the USB module.
The USB transceiver obtains power from the VUSB pin,
which is internally connected to a 3.3V internal
regulator. The best electrical signal quality is obtained
when VUSB is locally bypassed with a high-quality
ceramic capacitor.
The internal 3.3V regulator draws power from the VDD
pin. In certain scenarios, where VDD is lower than
3.3V+ internal LDO dropout, the VUSB pin must be tied
to an external regulated 3.3V. This will allow the USB
transceiver to work correctly, while the I/O voltage in
the rest of the system can be lower than 3.3V. As an
example, in a system where the MCP2210 is used and
the I/O required is of 2.2V, the VDD of the chip will be
tied to the 2.2V digital power rail, while the VUSB pin
must be connected to a regulated 3.3V power supply.
1.5.1
INTERNAL PULL-UP RESISTORS
The MCP2210 device has built-in pull-up resistors
designed to meet the requirements for full-speed USB.
1.5.2
MCP2210 POWER OPTIONS
The following are the main power options for the
MCP2210:
USB Bus Powered (5V)
Self Powered (from 3.3V to 5V), while the VUSB
pin is supplied with 3.3V (regulated). If the VDD is
powered with 5V, then the VUSB will be powered
by the internal regulator and the VUSB pin will
need only a decoupling capacitor
1.5.2.1
Internal Power Supply Details
MCP2210 offers various options for power supply. To
meet the required USB signaling levels, MCP2210
device incorporates an internal LDO used solely by the
USB transceiver, in order to present the correct D+/D
voltage levels.
Figure 1-1 shows the internal connections of the USB
transceiver LDO in relation with the VDD power supply
rail. The output of the USB transceiver LDO is tied to
the VUSB line.
A capacitor connected to the VUSB pin is required if the
USB transceiver LDO provides the 3.3V supply to the
transceiver.
FIGURE 1-1:
MCP2210 INTERNAL
POWER SUPPLY DETAILS
The provided VDD voltage has a direct influence on the
voltage levels present on the GPIO and SPI module
pins (GP8-GP0, MOSI, MISO and SCK). When VDD is
5V, all of these pins will have a logical ‘1’ around 5V
with the variations specified in Section 4.1 “DC Char-
For applications that require a 3.3V logical ‘1’ level,
VDD must be connected to a power supply providing
the 3.3V voltage. In this case, the internal USB
transceiver LDO cannot provide the required 3.3V
power. It is necessary to also connect the VUSB pin of
the MCP2210 to the 3.3V power supply rail. This way,
the USB transceiver is powered up directly from the
3.3V power supply.
1.5.2.2
USB Bus Powered (5V)
In Bus Power Only mode, the entire power for the
application is drawn from the USB (see Figure 1-2).
This is effectively the simplest power method for the
device.
FIGURE 1-2:
BUS POWER ONLY
LDO
3.3V
USB
Transceiver
D+
VDD
VUSB
D-
IN
OUT
VDD
VUSB
VSS
VBUS
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2210-I/SO | IC CONVERTER USB-PCI 20-SOIC |
| V28C48H100B3 | CONVERTER MOD DC/DC 48V 100W |
| VI-BTN-IX-F3 | CONVERTER MOD DC/DC 18.5V 75W |
| V28C48H100B | CONVERTER MOD DC/DC 48V 100W |
| V28C3V3H50BG3 | CONVERTER MOD DC/DC 3.3V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2210T-I/MQ | 功能描述:USB 接口集成電路 USB to SPI Protocol Converter RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2210T-I/SO | 功能描述:USB 接口集成電路 USB to SPI Protocol Converter RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2210T-I/SS | 功能描述:USB 接口集成電路 USB to SPI Protocol Converter RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2210T-I-MQ | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB-to-SPI Protocol Converter with GPIO (Master Mode) |
| MCP2210T-I-SO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB-to-SPI Protocol Converter with GPIO (Master Mode) |
發布緊急采購，3分鐘左右您將得到回復。