- 您現在的位置：買賣IC網 > PDF目錄3768 > MCP2200-I/SS (Microchip Technology)IC USB TO UART 20SSOP PDF資料下載
參數資料
| 型號： | MCP2200-I/SS |
| 廠商： | Microchip Technology |
| 文件頁數： | 41/44頁 |
| 文件大小： | 0K |
| 描述： | IC USB TO UART 20SSOP |
| 特色產品： | MCP2200 USB-to-UART Serial Converter |
| 標準包裝： | 67 |
| 特點： | USB 至 UART |
| 通道數： | 8 |
| FIFO's： | 256 字節 |
| 規程： | USB 2.0 |
| 電源電壓： | 3 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 684 (CN2011-ZH PDF) |
| 工具箱： | AC160135-1-KIT-ND - KIT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁
MCP2200
DS22228B-page 6
2011 Microchip Technology Inc.
1.5.2.1
Internal Power Supply Details
MCP2200 offers various options for power supply. To
meet the required USB signaling levels, MCP2200
device incorporates an internal LDO used solely by the
USB transceiver, in order to present the correct D+/D-
voltage levels.
Figure 1-2 shows the internal connections of the USB
transceiver LDO in relation with the VDD power supply
rail. The output of the USB transceiver LDO is tied to
the VUSB line. A capacitor connected to the VUSB pin is
required if the USB transceiver LDO provides the 3.3V
supply to the transceiver.
FIGURE 1-2:
MCP2200 INTERNAL
POWER SUPPLY DETAILS
The provided VDD voltage has a direct influence on the
voltage levels present on the GPIO pins (Rx/Tx and
RTS/CTS). When VDD is 5V, all of these pins will have
a logical ‘1’ around 5V with the variations specified in
For applications that require a 3.3V logical ‘1’ level,
VDD must be connected to a power supply providing
the 3.3V voltage. In this case, the internal USB trans-
ceiver LDO cannot provide the required 3.3V power. It
is necessary to also connect the VUSB pin of the
MCP2200 to the 3.3V power supply rail. This way, the
USB transceiver is powered up directly from the 3.3V
power supply.
1.5.2.2
USB Bus Powered (5V)
In Bus Power Only mode, all power for the application
is drawn from the USB (Figure 1-3). This is effectively
the simplest power method for the device.
FIGURE 1-3:
BUS POWER ONLY
In order to meet the inrush current requirements of the
USB 2.0 specifications, the total effective capacitance
appearing across VBUS and ground must be no more
than 10 F. If it is not more than 10 F, some kind of
inrush limiting is required. For more details on Inrush
Current Limiting, search for that subject in the current
Universal Serial Bus Specification
.
According to the USB 2.0 specification, all USB devices
must also support a Low-Power Suspend mode. In the
USB Suspend mode, devices must consume no more
than 500 A (or 2.5 mA for high powered devices that
are remote wake-up capable) from the 5V VBUS line of
the USB cable.
The host signals the USB device to enter Suspend
mode by stopping all USB traffic to that device for more
than 3 ms.
The USB bus provides a 5V voltage. However, the USB
transceiver requires 3.3V for the signaling (on D+ and
D- lines).
During USB Suspend mode, the D+ or D- pull-up
resistor must remain active, which will consume some
of
the
allowed
suspend
current
budget
(500 A/2.5 mA). The VUSB pin is required to have an
external bypass capacitor. It is recommended that the
capacitor be a ceramic cap, between 0.22 and 0.47 F.
Figure 1-4 shows a circuit where MCP2200’s internal
LDO is used to provide 3.3V to the USB transceiver.
The voltage on the VDD affects the voltage levels onto
the GPIO pins (Rx/Tx and RTS/CTS). With VDD at 5V,
these pins will have a logic ‘1’ of 5V with the variations
specified in Section 3.1, DC Characteristics.
LDO
3.3V
USB
Transceiver
D+
VDD
VUSB
D-
IN
OUT
VDD
VUSB
VSS
VBUS
相關PDF資料 |
PDF描述 |
|---|---|
| CAT9534YI-GT2 | IC I/O EXPANDER I2C 8B 16TSSOP |
| CAT9534WI-GT2 | IC I/O EXPANDER I2C 8B 16SOIC |
| ATMEGA8535L-8MUR | MCU AVR 8K FLASH 8MHZ 44QFN |
| PCA9535EDTR2G | 16-BIT I/O EXPANDER 24TSSOP |
| PCA9535ECMTTXG | 16-BIT I/O EXPANDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2200T-I/MQ | 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2200T-I/NQ | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO |
| MCP2200T-I/SO | 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2200T-I/SS | 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MCP2200T-IMQ | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO |
發布緊急采購，3分鐘左右您將得到回復。