- 您現在的位置：買賣IC網 > PDF目錄10453 > MCP2004A-E/MD (Microchip Technology)IC TXRX LIN W/VREG 8DFN PDF資料下載
參數資料
| 型號： | MCP2004A-E/MD |
| 廠商： | Microchip Technology |
| 文件頁數： | 23/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX LIN W/VREG 8DFN |
| 產品培訓模塊： | Microchip MCP20xx LIN Transceiver Overview |
| 標準包裝： | 91 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
2010-2011 Microchip Technology Inc.
DS22230D-page 3
MCP2003/4/3A/4A
1.0
DEVICE OVERVIEW
The MCP2003/4/3A/4A devices provide a physical
interface between a microcontroller and a LIN bus.
These devices will translate the CMOS/TTL logic levels
to LIN logic level, and vice versa. It is intended for
automotive and industrial applications with serial bus
speeds up to 20 Kbaud.
LIN specification 2.1 requires that the transceiver of all
nodes in the system is connected via the LIN pin, refer-
enced to ground and with a maximum external
termination resistance load of 510
Ω from LIN bus to
battery supply. The 510
Ω corresponds to 1 master and
15 slave nodes.
The VREN pin can be used to drive the logic input of an
external voltage regulator. This pin is high in all modes
except for Power-Down mode.
1.1
External Protection
1.1.1
REVERSE BATTERY PROTECTION
An external reverse-battery-blocking diode should be
used to provide polarity protection (see Example 1-1).
1.1.2
TRANSIENT VOLTAGE
PROTECTION (LOAD DUMP)
An external 43V transient suppressor (TVS) diode,
between VBB and ground, with a 50
Ω transient
protection resistor (RTP) in series with the battery
supply and the VBB pin serve to protect the device from
power transients (see Example 1-1) and ESD events.
While this protection is optional, it is considered good
engineering practice.
1.2
Internal Protection
1.2.1
ESD PROTECTION
For component-level ESD ratings, please refer to the
maximum operation specifications.
1.2.2
GROUND LOSS PROTECTION
The LIN Bus specification states that the LIN pin must
transition to the recessive state when ground is
disconnected. Therefore, a loss of ground effectively
forces the LIN line to a high-impedance level.
1.2.3
THERMAL PROTECTION
The thermal protection circuit monitors the die
temperature and is able to shut down the LIN
transmitter.
There are two causes for a thermal overload. A thermal
shut down can be triggered by either, or both, of the
following thermal overload conditions.
LIN bus output overload
Increase in die temperature due to increase in
environment temperature
Driving the TXD and checking the RXD pin makes it
possible to determine whether there is a bus contention
(Rx = low, Tx = high) or a thermal overload condition
(Rx = high, Tx = low). After a thermal overload event,
the device will automatically recover once the die
temperature has fallen below the recovery temperature
threshold. See Figure 1-1.
FIGURE 1-1:
THERMAL SHUTDOWN
STATE DIAGRAM
Operation
Mode
Transmitter
Shutdown
LIN bus
Shorted
to VBB
Temp < SHUTDOWN
TEMP
相關PDF資料 |
PDF描述 |
|---|---|
| VE-27T-IW-F2 | CONVERTER MOD DC/DC 6.5V 100W |
| VE-27T-IW-F1 | CONVERTER MOD DC/DC 6.5V 100W |
| MCP2003A-E/MD | IC TXRX LIN W/VREG 8DFN |
| MCP2004AT-E/MD | IC TXRX LIN W/VREG 8DFN |
| VE-BT4-IV-F2 | CONVERTER MOD DC/DC 48V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2004AT-E/MD | 功能描述:LIN 收發器 Stand alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2004AT-E/SN | 功能描述:LIN 收發器 Stand alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2004-E/MD | 功能描述:LIN 收發器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2004-E/P | 功能描述:LIN 收發器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP2004-E/SN | 功能描述:LIN 收發器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
發布緊急采購，3分鐘左右您將得到回復。