- 您現在的位置：買賣IC網 > PDF目錄383586 > MCP1727 (Microchip Technology Inc.) 1.5A, Low Voltage, Low Quiescent Current LDO Regulator PDF資料下載
參數資料
| 型號： | MCP1727 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
| 中文描述： | 1.5安培的電流，低電壓，低靜態電流LDO穩壓器 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 678K |
| 代理商： | MCP1727 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
MCP1727
DS21999B-page 14
2007 Microchip Technology Inc.
3.0
PIN DESCRIPTION
The descriptions of the pins are listed in
Table 3-1
.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Input Voltage Supply (V
IN
)
Connect the unregulated or regulated input voltage
source to V
IN
. If the input voltage source is located
several inches away from the LDO, or the input source
is a battery, it is recommended that an input capacitor
be used. A typical input capacitance value of 1 μF to
10 μF should be sufficient for most applications.
3.2
Shutdown Control Input (SHDN)
The SHDN input is used to turn the LDO output voltage
on and off. When the SHDN input is at a logic-high
level, the LDO output voltage is enabled. When the
SHDN input is pulled to a logic-low level, the LDO
output voltage is disabled. When the SHDN input is
pulled low, the PWRGD output also goes low and the
LDO enters a low quiescent current shutdown state
where the typical quiescent current is 0.1 μA.
3.3
Ground (GND)
Connect the GND pin of the LDO to a quiet circuit
ground. This will help the LDO power supply rejection
ratio and noise performance. The ground pin of the
LDO only conducts the quiescent current of the LDO
(typically 120 μA), so a heavy trace is not required.
For applications have switching or noisy inputs tie the
GND pin to the return of the output capacitor. Ground
planes help lower inductance and voltage spikes
caused by fast transient load currents and are
recommended for applications that are subjected to
fast load transients.
3.4
Power Good Output (PWRGD)
The PWRGD output is an open-drain output used to
indicate when the LDO output voltage is within 92%
(typically) of its nominal regulation value. The PWRGD
threshold has a typical hysteresis value of 2%. The
PWRGD output is typically delayed by 200 μs (typical,
no capacitance on C
DELAY
pin) from the time the LDO
output is within 92% + 3% (max hysteresis) of the
regulated output value on power-up. This delay time is
controlled by the C
DELAY
pin.
3.5
Power Good Delay Set-Point Input
(C
DELAY
)
The C
DELAY
input sets the power-up delay time for the
PWRGD output. By connecting an external capacitor
from the C
DELAY
pin to ground, the typical delay times
for the PWRGD output can be adjusted from 200 μs (no
capacitance) to 300 ms (0.1 μF capacitor). This allows
for the optimal setting of the system reset time.
3.6
Output Voltage Sense/Adjust Input
(ADJ/Sense)
3.6.1
ADJ
For adjustable applications, the output voltage is
connected to the ADJ input through a resistor divider
that sets the output voltage regulation value. This
provides the user the capability to set the output
voltage to any value they desire within the 0.8V to 5.0V
range of the device.
Fixed Output
Adjustable
Output
Name
Description
1
1
V
IN
V
IN
SHDN
Input Voltage Supply
2
2
Input Voltage Supply
3
3
Shutdown Control Input (active-low)
4
4
GND
Ground
5
5
PWRGD
Power Good Output (open-drain)
6
6
C
DELAY
ADJ
Power Good Delay Set-Point Input
—
7
Voltage Sense Input (adjustable version)
7
—
Sense
Voltage Sense Input (fixed voltage version)
8
8
V
OUT
EP
Regulated Output Voltage
Exposed Pad
Exposed Pad
Exposed Pad of the DFN Package (ground potential)
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1801 | 150 mA, High PSRR, Low Quiescent Current LDO |
| MCP1802 | 300 mA, High PSRR, Low Quiescent Current LDO |
| MCP1827T-1202EAB | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1827-5002EAB | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1827-5002EAT | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1727-0802E/MF | 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO .8V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1727-0802E/SN | 功能描述:低壓差穩壓器 - LDO 1.5A Vout=0.8V Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1727-1202E/MF | 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO 1.2V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1727-1202E/SN | 功能描述:低壓差穩壓器 - LDO 1.5A Vout=1.2V Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1727-1802E/MF | 功能描述:低壓差穩壓器 - LDO 1.5A CMOS LDO 1.8V DFN8 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。