- 您現在的位置：買賣IC網 > PDF目錄296502 > MCP1603-ADJI/MC 0.5 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | MCP1603-ADJI/MC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 3 MM, 0.90 MM HEIGHT, PLASTIC, DFN-8 |
| 文件頁數： | 5/26頁 |
| 文件大?。?/td> | 758K |
| 代理商： | MCP1603-ADJI/MC |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
2007 Microchip Technology Inc.
DS22042A-page 13
MCP1603
4.3
Soft Start
The output of the MCP1603 is controlled during start-
up. This control allows for a very minimal amount of
VOUT overshoot during start-up from VIN rising above
the UVLO voltage or SHDN being enabled.
4.4
Overtemperature Protection
Overtemperature protection circuitry is integrated in the
MCP1603. This circuitry monitors the device junction
temperature and shuts the device off, if the junction
temperature exceeds the typical 150°C threshold. If
this threshold is exceeded, the device will automatically
restart once the junction temperature drops by
approximately 10°C. The soft start is reset during an
overtemperture condition.
4.5
Overcurrent Protection
Cycle-by-cycle current limiting is used to protect the
MCP1603 from being damaged when an external short
circuit is applied. The typical peak current limit is
860 mA. If the sensed current reaches the 860 mA
limit, the P-Channel MOSFET is turned off, even if the
output voltage is not in regulation. The device will
attempt to start a new switching cycle when the internal
oscillator sets the internal RS latch.
4.6
Enable/Disable Control
The SHDN pin is used to enable or disable the
MCP1603. When the SHDN pin is pulled low, the
device is disabled. When pulled high the device is
enabled and begins operation provided the input
voltage is not below the UVLO threshold or a fault
condition exists.
4.7
Undervoltage Lockout (UVLO)
The UVLO feature uses a comparator to sense the
input voltage (VIN) level. If the input voltage is lower
than the voltage necessary to properly operate the
MCP1603, the UVLO feature will hold the converter off.
When VIN rises above the necessary input voltage, the
UVLO is released and soft start begins. Hysteresis is
built into the UVLO circuit to compensate for input
impedance. For example, if there is any resistance
between the input voltage source and the device when
it is operating, there will be a voltage drop at the input
to the device equal to IIN x RIN. The typical hysteresis
is 140 mV.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1700-1202ETO | Low Quiescent Current LDO |
| MCP1700-1802ETO | Low Quiescent Current LDO |
| MCP1700-2502ETO | Low Quiescent Current LDO |
| MCP1700-3002ETO | Low Quiescent Current LDO |
| MCP1700-3302ETO | Low Quiescent Current LDO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1603B | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.0 MHz, 500 mA Synchronous Buck Regulator |
| MCP1603BT-180I/OS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.0 MHz, 500 mA Synchronous Buck Regulator |
| MCP1603BT-330I/OS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.0 MHz, 500 mA Synchronous Buck Regulator |
| MCP1603BT-ADJI/OS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.0 MHz, 500 mA Synchronous Buck Regulator |
| MCP1603EV | 功能描述:電源管理IC開發工具 MCP1603 Buck Converter Eval Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。