參數資料
型號: MC9S08SF4MTJ
廠商: Freescale Semiconductor
文件頁數: 27/30頁
文件大小: 0K
描述: MCU 8BIT 4K FLASH 20-TSSOP
標準包裝: 75
系列: S08
核心處理器: S08
芯體尺寸: 8-位
速度: 40MHz
連通性: I²C
外圍設備: LVD,POR,PWM,WDT
輸入/輸出數: 18
程序存儲器容量: 4KB(4K x 8)
程序存儲器類型: 閃存
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 8x10b
振蕩器型: 外部
工作溫度: -40°C ~ 125°C
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
包裝: 管件
MC9S08SF4 Series MCU Data Sheet, Rev. 4
Thermal Characteristics
Freescale Semiconductor
6
3.4
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and voltage regulator circuits and it is user-determined rather than being controlled by the
MCU design. To take PI/O into account in power calculations, determine the difference between actual pin
voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high
pin current (heavy loads), the difference between pin voltage and VSS or VDD will be small.
The average chip-junction temperature (TJ) in C can be obtained from:
TJ = TA + (PD JA)
Eqn. 1
Table 2. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to 5.8
V
Maximum current into VDD
IDD
120
mA
Digital input voltage
VIn
–0.3 to VDD +0.3
V
Instantaneous maximum current
Single pin limit (applies to all port pins)1, 2, 3
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2 All functional non-supply pins are internally clamped to V
SS and VDD.
3 Power supply must maintain regulation within operating V
DD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in the external power supply going
out of regulation. Ensure external VDD load shunts current greater than the maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
ID
25
mA
Storage temperature range
Tstg
–55 to 150
C
Table 3. Thermal Characteristics
Rating
Symbol
Value
Unit
Operating temperature range
(packaged)
TA
TL to TH
–40 to 125
C
Thermal resistance (single-layer board)
20-pin TSSOP
16-pin TSSOP
JA
115
123
C/W
Thermal resistance (four-layer board)
20-pin TSSOP
16-pin TSSOP
JA
76
75
C/W
相關PDF資料
PDF描述
MC9S08QE4CWJ IC MCU 8BIT 4K FLASH 20-SOIC
MC9S08SH4CWJ MCU 8BIT 4K FLASH 20-SOIC
MC9S08JS8CWJ IC MCU 8BIT 8K FLASH 20SOIC
8-227079-1 PLUG, COML BNC, KIT
MC9S08JS8CFK IC MCU 8BIT 8K FLASH 24QFN
相關代理商/技術參數
參數描述
MC9S08SF4VTG 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Data
MC9S08SF4VTJ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Data
MC9S08SG16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCS08 Microcontrollers
MC9S08SG16E1CTGR 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCS08 Microcontrollers
MC9S08SG16E1CTJR 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCS08 Microcontrollers