參數資料
型號: MC9S08QE4CTG
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO16
封裝: 0.65 MM PITCH, ROHS COMPLIANT, TSSOP-16
文件頁數: 24/46頁
文件大小: 1293K
代理商: MC9S08QE4CTG
MC9S08QE8 Series Data Sheet, Rev. 7
Ordering Information
Freescale Semiconductor
30
3.14.1
Conducted Transient Susceptibility
Microcontroller transient conducted susceptibility is measured in accordance with an internal Freescale
test method. The measurement is performed with the microcontroller installed on a custom EMC
evaluation board and running specialized EMC test software designed in compliance with the test method.
The conducted susceptibility is determined by injecting the transient susceptibility signal on each pin of
the microcontroller. The transient waveform and injection methodology is based on IEC 61000-4-4
(EFT/B). The transient voltage required to cause performance degradation on any pin in the tested
configuration is greater than or equal to the reported levels unless otherwise indicated by footnotes below
The susceptibility performance classification is described in Table 20.
4
Ordering Information
This section contains ordering information for the device numbering system.
Example of the device numbering system:
Table 19. Conducted Susceptibility, EFT/B
Parameter
Symbol
Conditions
fOSC/fBUS
Result
Amplitude1
(Min)
1 Data based on qualification test results. Not tested in production.
Unit
Conducted susceptibility, electrical
fast transient/burst (EFT/B)
VCS_EFT
VDD = 3.3 V
TA = 25
oC
package type
32-pin LQFP
8 MHz
crystal
8 MHz bus
A2.3
kV
B4.0
C>4.0
D>4.0
Table 20. Susceptibility Performance Classification
Result
Performance Criteria
A
No failure
The MCU performs as designed during and after exposure.
B
Self-recovering
failure
The MCU does not perform as designed during exposure. The MCU returns
automatically to normal operation after exposure is removed.
C
Soft failure
The MCU does not perform as designed during exposure. The MCU does not return to
normal operation until exposure is removed and the RESET pin is asserted.
D
Hard failure
The MCU does not perform as designed during exposure. The MCU does not return to
normal operation until exposure is removed and the power to the MCU is cycled.
E
Damage
The MCU does not perform as designed during and after exposure. The MCU cannot
be returned to proper operation due to physical damage or other permanent
performance degradation.
相關PDF資料
PDF描述
MC9S08SF4CTG MICROCONTROLLER, PDSO16
MC9S08SF4CTJ MICROCONTROLLER, PDSO20
MC9S12A128BCPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
MC9S12A128BCPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
MC9S12D64VPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
相關代理商/技術參數
參數描述
MC9S08QE4CTGR 功能描述:8位微控制器 -MCU 4K Flash, 256 Ram RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QE4CWJ 功能描述:8位微控制器 -MCU 4KB FLASH; 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QE4CWL 功能描述:8位微控制器 -MCU 4KB FLASH; 512 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QE64CFT 功能描述:8位微控制器 -MCU 8 BIT, 64K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QE64CLC 功能描述:8位微控制器 -MCU 8 BIT 64K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT