- 您現在的位置：買賣IC網 > PDF目錄11943 > MC9RS08KA2CSC (Freescale Semiconductor)IC MCU 8-BIT 2K FLASH 8-SOIC PDF資料下載
參數資料
| 型號： | MC9RS08KA2CSC |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 132/136頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 8-BIT 2K FLASH 8-SOIC |
| 產品培訓模塊： | Mechatronics USBSpyder08 Discovery Kit RS08KA2 Low-End Microcontroller Series MC9RS08KA8 Microcontroller |
| 標準包裝： | 98 |
| 系列： | RS08 |
| 核心處理器： | RS08 |
| 芯體尺寸： | 8-位 |
| 速度： | 10MHz |
| 外圍設備： | LVD，POR，WDT |
| 輸入/輸出數： | 4 |
| 程序存儲器容量： | 2KB（2K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 63 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 包裝： | 管件 |
| 產品目錄頁面： | 726 (CN2011-ZH PDF) |
| 配用： | DEMO9RS08KA2-ND - DEMO BOARD FOR 9RS08KA2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁當前第132頁第133頁第134頁第135頁第136頁
Modulo Timer (RS08MTIMV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
95
11.4
Functional Description
The MTIM is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector,
and a prescaler block with nine selectable values. The module also contains software selectable interrupt
logic.
The MTIM counter (MTIMCNT) has three modes of operation: stopped, free-running, and modulo. Out
of reset, the counter is stopped. If the counter is started without writing a new value to the modulo register,
then the counter will be in free-running mode. The counter is in modulo mode when a value other than $00
is in the modulo register while the counter is running.
After any MCU reset, the counter is stopped and reset to $00, and the modulus is set to $00. The bus clock
is selected as the default clock source and the prescale value is divide by 1. To start the MTIM in
free-running mode, simply write to the MTIM status and control register (MTIMSC) and clear the MTIM
stop bit (TSTP).
Four clock sources are software selectable: the internal bus clock, the fixed frequency clock (XCLK), and
an external clock on the TCLK pin, selectable as incrementing on either rising or falling edges. The MTIM
clock select bits (CLKS) in MTIMCLK are used to select the desired clock source. If the counter is active
(TSTP = 0) when a new clock source is selected, the counter will continue counting from the previous
value using the new clock source.
Nine prescale values are software selectable: clock source divided by 1, 2, 4, 8, 16, 32, 64, 128, or 256.
The prescaler select bits (PS) in MTIMCLK select the desired prescale value. If the counter is active
(TSTP = 0) when a new prescaler value is selected, the counter will continue counting from the previous
value using the new prescaler value.
The MTIM modulo register (MTIMMOD) allows the overflow compare value to be set to any value from
$01 to $FF. Reset clears the modulo value to $00, which results in a free running counter.
When the counter is active (TSTP = 0), the counter increments at the selected rate until the count matches
the modulo value. When these values match, the counter overflows to $00 and continues counting. The
MTIM overflow flag (TOF) is set whenever the counter overflows. The flag sets on the transition from the
modulo value to $00. Writing to MTIMMOD while the counter is active resets the counter to $00 and
clears TOF.
Clearing TOF is a two-step process. The first step is to read the MTIMSC register while TOF is set. The
second step is to write a 0 to TOF. If another overflow occurs between the first and second steps, the
clearing process is reset and TOF will remain set after the second step is performed. This will prevent the
second occurrence from being missed. TOF is also cleared when a 1 is written to TRST or when any value
is written to the MTIMMOD register.
The MTIM allows for an optional interrupt to be generated whenever TOF is set. To enable the MTIM
overflow interrupt, set the MTIM overflow interrupt enable bit (TOIE) in MTIMSC. TOIE must never be
written to a 1 while TOF = 1. Instead, TOF must be cleared first, then the TOIE can be set to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| 1588172-2 | MPO ADAPTER ASSY. W/CLIP |
| VI-B4L-CU-F1 | CONVERTER MOD DC/DC 28V 200W |
| VI-B4K-CU-F2 | CONVERTER MOD DC/DC 40V 200W |
| 501933-2 | BKHD ASSY FSD,B, PANEL MT EARS |
| 501933-3 | BKHD ASSY FSD,M, PANEL MT EARS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC9RS08KA2CSCR | 功能描述:8位微控制器 -MCU 2K FLASH W/ ACMP 62 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC9RS08KA2DB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA2PC | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA2SC | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC9RS08KA4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MCU Block Diagram |
發布緊急采購，3分鐘左右您將得到回復。