參數資料
型號: MC9328MX21SCVM
廠商: Freescale Semiconductor
文件頁數: 77/88頁
文件大?。?/td> 0K
描述: IC MPU I.MX21S 289-MAPBGA
標準包裝: 90
系列: i.MX21
核心處理器: ARM9
芯體尺寸: 32-位
速度: 266MHz
連通性: 1 線,EBI/EMI,I²C,IrDA,MMC,智能卡,SPI,SSI,UART/USART,USB OTG
外圍設備: DMA,I²S,LCD,POR,PWM,WDT
輸入/輸出數: 192
程序存儲器類型: ROMless
電壓 - 電源 (Vcc/Vdd): 1.45 V ~ 3.3 V
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 289-LFBGA
包裝: 托盤
Specifications
MC9328MX21S Technical Data, Rev. 1.3
Freescale Semiconductor
79
3.19
DTACK Mode Memory Access Timing Diagrams
When enabled, the DTACK input signal is used to externally terminate a data transfer. For DTACK
enabled operations, a bus time-out monitor generates a bus error when an external bus cycle is not
terminated by the DTACK input signal after 1024 HCLK clock cycles have elapsed, where HCLK is the
internal system clock driven from the PLL module. For a 133 MHz HCLK setting, this time equates to
7.7
μs. Refer to the Section 3.5, “DPLL Timing Specifications” for more information on how to generate
different HCLK frequencies.
There are two modes of operation for the DTACK input signal: rising edge detection or level sensitive
detection with a programmable insensitivity time. DTACK is only used during external asynchronous data
transfers, thus the SYNC bit in the chip select control registers must be cleared.
During edge detection mode, the EIM will terminate an external data transfer following the detection of
the DTACK signal’s rising edge, so long as it occurs within the 1024 HCLK cycle time. Edge detection
mode is used for devices that follow the PCMCIA standard. Note that DTACK rising edge detection mode
can only be used for CS[5] operations. To configure CS[5] for DTACK rising edge detection, the following
bits must be programmed in the Chip Select 5 Control Register and EIM Configuration Register:
WSC bit field set to 0x3F and CSA (or CSN) set to 1 or greater in the Chip Select 5 Control Register
AGE bit set in the EIM Configuration Register
Other bits such as DSZ, OEA, OEN, and so on, may be set according to system and timing requirements
of the external device. The requirement of setting CSA or CSN is required to allow the EIM to wait for the
rising edge of DTACK during back-to-back external transfers, such as during DMA transfers or an internal
32-bit access through an external 16-bit data port.
During level sensitive detection, the EIM will first hold off sampling the DTACK signal for at least 2
HCLK cycles, and up to 5 HCLK cycles as programmed by the DCT bits in the Chip Select Control
Register. After this insensitivity time, the EIM will sample DTACK and if it detects that DTACK is logic
high, it will continue the data transfer at the programmed number of wait states. However, if the EIM
detects that DTACK is logic low, it will wait until DTACK goes to logic high to continue the access, so
long as this occurs within the 1024 HCLK cycle time. If at anytime during an external data transfer
DTACK goes to logic low, the EIM will wait until DTACK returns to logic high to resume the data transfer.
Level detection is often used for asynchronous devices such graphic controller chips. Level detection may
be used with any chip select except CS[4] as it is multiplexed with the DTACK signal. To configure a chip
select for DTACK level sensitive detection, the following bits must be programmed in the Chip Select
Control Register and EIM Configuration Register:
EW bit set, WSC set to > 1, and CSN set to < 3 in the Chip Select Control Register
BCD/DCT set to desired “insensitivity time” in the Chip Select Control Register. The “insensitivity time”
is dictated by the external device’s timing requirements.
AGE bit cleared in the EIM Configuration Register
Other bits such as DSZ, OEA, OEN, and so on, may be set according to system and timing requirements
of the external device.
The waveforms in the following section provide examples of the DTACK signal operation.
Because
of
an
order
from
the
United
States
International
Trade
Commission,
BGA-packaged
product
lines
and
part
numbers
indicated
here
currently
are
not
available
from
Freescale
for
import
or
sale
in
the
United
States
prior
to
September
2010:
i.MX21
Product
Family
相關PDF資料
PDF描述
PK30X256VLQ100 IC ARM CORTEX MCU 256K 144-LQFP
MC9328MXSVP10 IC MCU I.MXS 100MHZ 225-MAPBGA
MCIMX27LMOP4AR2 IC MPU I.MX27 IN 19X19 473MAPBGA
VI-B7H-IX-B1 CONVERTER MOD DC/DC 52V 75W
S912XEQ512J3MAG MCU 16BIT 512K FLASH 144LQFP
相關代理商/技術參數
參數描述
MC9328MX21SCVMR2 功能描述:處理器 - 專門應用 DB I.MX21 17X17 PB-FR RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MC9328MX21SVK 功能描述:處理器 - 專門應用 DB I.MX21S RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MC9328MX21SVKR2 功能描述:處理器 - 專門應用 DB I.MX21S RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MC9328MX21SVM 功能描述:處理器 - 專門應用 DB I.MX21 17X17 PB-FR RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MC9328MX21SVMR2 功能描述:處理器 - 專門應用 DB I.MX21 17X17 PB-FR RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432