- 您現在的位置：買賣IC網 > PDF目錄45283 > MC908QT1AVFQ (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, DSO8 PDF資料下載
參數資料
| 型號： | MC908QT1AVFQ |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, DSO8 |
| 封裝： | 4 X 4 MM, 1 MM HEIGHT, 0.80 MM PITCH, DFN-8 |
| 文件頁數： | 108/200頁 |
| 文件大?。?/td> | 2588K |
| 代理商： | MC908QT1AVFQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁當前第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
908QTA/QYxA Conversion Guidelines
MC68HC908QYA/QTA Family Data Sheet, Rev. 1
196
Freescale Semiconductor
A.3 Conversion Considerations
Enhancements lead to slight differences in operation from QYx Classic to the QYxA. There are a few
points that should be considered in the conversion process.
The Monitor ROM changed from 2 K to 1 K in size. This has led to the limitation that programming
across page boundaries is no longer supported by the on-chip program range routine. Also, in very
rare cases, ROM code improvements could cause customers to have to modify a few instructions
in their application code. For example, when performing a mass erase, a valid address is required
instead of an unspecified address.
The QYxA contains new modules like the 10-bit ADC and OSC. In rare cases, new modules could
cause customers to have to modify a few instructions in their application code. For example, if ADC
code was written so that entire registers are configured without respect to reserve bits, then the
ADC code will need to be revised to work correctly on the QYxA.
The Reference Clock for ADC conversions has changed from the bus clock to the system clock
(Bus Clock * 4). A change to the divide register may be necessary to set the reference clock to a
specified value.
A.4 Code Changes Checklist
Below is a checklist that should be reviewed in the conversion process. This checklist will point out all the
issues that should be addressed as your code is ported.
1.
Does the original software use Auxiliary ROM routines (for example, Getbyte, Putbyte, delnus)?
If so, the software will have to be changed to handle new Auxiliary ROM routines, addresses of
these routines have changed in QYxA. Code will have to be changed to use the proper addresses.
2.
Does the software use FLASH as EEPROM?
If so, there are several possible issues for the page erase and mass erase routine. Software will
have to be checked to ensure that proper procedure is used and the CTRLBYT is set with a MOV
instruction not a BSET. Also, on-chip FLASH programming routines can no longer program across
row boundaries
3.
Does the code use the auto wake up timer and does the application depend on the typical auto
wake time out?
Since the timeout has been improved for QYxA it may be necessary to modify software to
compensate for the change in timeout.
4.
Bits changed in the OSCSC, CONFIG2, and ADC registers?
Any code that writes to these registers should be reviewed to ensure that the writes are not
affecting the changed bits
5.
Does the code use external OSC, crystal, or RC?
If so, since the OSCOPT bits have changed locations code will have to be updated to update these
bits in their proper locations.
6.
Does the code use the ADC?
If so, because on QYxA the ADC clock is driven from 4XBUSCLK instead of BUSCLK changes to
the ADC clock divider bits may be needed to maintain proper operation.
相關PDF資料 |
PDF描述 |
|---|---|
| MC908QT4AVDW | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8 |
| MC908QY4AVDW | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
| MC908QY1AVDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
| MC908QY2AVP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP16 |
| MC908QY2AVDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC908QT1CDTE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC908QT1CDWE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC908QT1CFQE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers |
| MC908QT1CPE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers |
| MC908QT1DTE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。