- 您現在的位置：買賣IC網 > PDF目錄376153 > MC80F0208K (Electronic Theatre Controls, Inc.) 8-BIT SINGLE-CHIP MICROCONTROLLERS PDF資料下載
參數資料
| 型號： | MC80F0208K |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| 中文描述： | 8位單晶片微控制器 |
| 文件頁數： | 103/128頁 |
| 文件大?。?/td> | 1408K |
| 代理商： | MC80F0208K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁當前第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Preliminary
MC80F0208/16/24
MAR. 2005 Ver 0.2
99
Figure 21-6 Timing of STOP Mode Release by Reset
21.3 Stop Mode at Internal RC-Oscillated Watchdog Timer Mode
In the Internal RC-Oscillated Watchdog Timer mode, the on-chip
oscillator is stopped. But internal RC oscillation circuit is oscil-
lated in this mode. The on-chip RAM and Control registers are
held. The port pins out the values held by their respective port
data register, port direction registers.
The Internal RC-Oscillated Watchdog Timer mode is activated
by execution of STOP instruction after setting the bit RCWDT of
CKCTLR to "1". (This register should be written by byte opera-
tion. If this register is set by bit manipulation instruction, for ex-
ample "set1" or "clr1" instruction, it may be undesired operation)
Note:
Caution: After STOP instruction, at least two or more
NOP instruction should be written
Ex)
LDM WDTR,#1111_1111B
LDM CKCTLR,#0010_1110B
LDM SSCR,#0101_1010B
STOP
NOP ;for stabilization time
NOP ;for stabilization time
The exit from Internal RC-Oscillated Watchdog Timer mode is
hardware reset or external interrupt or watchdog timer interrupt
(at RC-watchdog timer mode). Reset re-defines all the Control
registers but does not change the on-chip RAM. External inter-
rupts allow both on-chip RAM and Control registers to retain
their values.
If I-flag = 1, the normal interrupt response takes place. In this
case, if the bit WDTON of CKCTLR is set to "0" and the bit
WDTE of IENH is set to "1", the device will execute the watch-
dog timer interrupt service routine(Figure 8-6). However, if the
bit WDTON of CKCTLR is set to "1", the device will generate
the internal Reset signal and execute the reset processing(Figure
21-8). If I-flag = 0, the chip will resume execution starting with
the instruction following the STOP instruction. It will not vector
to interrupt service routine.(refer to Figure 21-4)
When exit from Stop mode at Internal RC-Oscillated Watchdog
Timer mode by external interrupt, the oscillation stabilization
time is required to normal operation. Figure 21-7 shows the tim-
ing diagram. When release the Internal RC-Oscillated Watchdog
Timer mode, the basic interval timer is activated on wake-up. It
is increased from 00
H
until FF
H
. The count overflow is set to start
normal operation. Therefore, before STOP instruction, user must
be set its relevant prescaler divide ratio to have long enough time
(more than 20msec). This guarantees that oscillator has started
and stabilized. By reset, exit from internal RC-Oscillated Watch-
dog Timer mode is shown in Figure 21-8.
~
STOP Mode
Time can not be control by software
Oscillator
(XI pin)
~
~
~
STOP Instruction Execution
Stabilization Time
t
ST
= 65.5mS @4MHz
Internal
Clock
Internal
RESET
~
~
~
~
~
RESET
相關PDF資料 |
PDF描述 |
|---|---|
| MC80F0208Q | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216 | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216K | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216Q | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0224 | 8-BIT SINGLE-CHIP MICROCONTROLLERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC80F0208Q | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0216Q | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0224 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。