- 您現在的位置：買賣IC網 > PDF目錄45276 > MC80C52CXXX-30P883 (ATMEL CORP) 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MC80C52CXXX-30P883 |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, SIDE BRAZED, DIP-40 |
| 文件頁數： | 33/81頁 |
| 文件大?。?/td> | 663K |
| 代理商： | MC80C52CXXX-30P883 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
39
ATtiny28L/V
1062F–AVR–07/06
Hardware Modulator
ATtiny28 features a built-in hardware modulator connected to a high-current output pad,
PA2. The hardware modulator generates a configurable pulse train. The on-time of a
pulse can be set to a number of chip clock cycles. This is done by configuring the Modu-
lation Control Register (MODCR).
PA2 is the built-in, high-current LED driver and it is always an output pin. The output
buffer can sink 25 mA at V
CC = 2.0V. When MCONF is zero, modulation is switched off
and the pin acts as a normal high-current output pin. The following truth table shows the
effect of various PORTA2 and MCONF settings.
The modulation period is available as a prescale to Timer/Counter0 and thus, this timer
should be used to time the length of each burst. If the number of pulses to be sent is N,
the number 255 - N should be loaded to the timer. When an overflow occurs, the trans-
mission is complete.The OOM01 and OOM00 bits in TCCR0 can be configured to
automatically change the value on PA2 when a Timer/Counter0 overflow occurs. See
“Timer/Counter0” on page 34 for details on how to configure the OOM01 and OOM00
bits.
The modulation period is available as a prescale even when PORTA2 is high and mod-
ulation is stopped. Thus, this prescale can also be used to time the intervals between
bursts.
To get a glitch-free output, the user should first configure the MODCR register to enable
modulation. There are two ways to start the modulation:
1.
Clear the PORTA2 bit in Port A Data Register (PORTA).
2.
Configure OOM00 and OOM01 bits in the Timer/Counter0 Control Register
(TCCR0) to clear PA2 on the next overflow. Either an overflow or a forced over-
flow can then be used to start modulation.
The PA2 output will then be set low at the start of the next cycle. To stop the modulated
output, the user should set the PORTA2 bit or configure OOM00 and OOM01 to set PA2
on the next overflow. If the MODCR register is changed during modulation, the changed
value will take effect at the start of the next cycle, producing a glitch-free output. See
Table 16. PA2 Output
PORTA2
MCONF
PA2 Output
00
0
1 - 7
Modulated
1X
1
相關PDF資料 |
PDF描述 |
|---|---|
| MR80C32-20/883:RD | 8-BIT, 20 MHz, MICROCONTROLLER, CQCC44 |
| MC80C52XXX-16SBD | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MR83C154XXX-12P883D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44 |
| MC80C52TXXX-25P883D | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CDIP40 |
| IF280C51T-20R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC80D21000G | 制造商:COR 功能描述:RN |
| MC80F0104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。