參數資料
型號： MC705C9ACPE
廠商： Freescale Semiconductor
文件頁數： 48/118頁
文件大?。?/td> 0K
描述： IC MCU 2.1MHZ 16K OTP 40-DIP
標準包裝： 9
系列： HC05
核心處理器： HC05
芯體尺寸： 8-位
速度： 2.1MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 24
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： OTP
RAM 容量： 352 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 40-DIP（0.600"，15.24mm）
包裝： 管件
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
Freescale Semiconductor
35
Chapter 4
Interrupts
4.1 Introduction
The MCU can be interrupted by five different sources, four maskable hardware interrupts, and one
non-maskable software interrupt:
External signal on the IRQ pin or port B pins
16-bit programmable timer
Serial communications interface
Serial peripheral interface
Software interrupt instruction (SWI)
Interrupts cause the processor to save register contents on the stack and to set the interrupt mask (I bit)
to prevent additional interrupts. The RTI instruction causes the register contents to be recovered from the
stack and normal processing to resume.
Unlike reset, hardware interrupts do not cause the current instruction execution to be halted, but are
considered pending until the current instruction is complete.
NOTE
The current instruction is the one already fetched and being operated on.
When the current instruction is complete, the processor checks all pending hardware interrupts. If
interrupts are not masked (CCR I bit clear) and if the corresponding interrupt enable bit is set, the
processor proceeds with interrupt processing; otherwise, the next instruction is fetched and executed.
If an external interrupt and a timer, SCI, or SPI interrupt are pending at the end of an instruction execution,
the external interrupt is serviced first. The SWI is executed the same as any other instruction, regardless
of the I-bit state.
Table 4-1 shows the relative priority of all the possible interrupt sources. Figure 4-1 shows the interrupt
processing flow.
4.2 Non-Maskable Software Interrupt (SWI)
The SWI is an executable instruction and a non-maskable interrupt: It is executed regardless of the state
of the I bit in the CCR. If the I bit is zero (interrupts enabled), SWI executes after interrupts which were
pending when the SWI was fetched, but before interrupts generated after the SWI was fetched. The
interrupt service routine address is specified by the contents of memory locations $3FFC and $3FFD.
相關PDF資料
PDF描述
2-6457567-2 ADPTR,DUP,LC,SR BLU,CER,LOGO
V24A28T400BF3 CONVERTER MOD DC/DC 28V 400W
V24A28T400BF2 CONVERTER MOD DC/DC 28V 400W
V24A24T400BG3 CONVERTER MOD DC/DC 24V 400W
V24A24T400BG2 CONVERTER MOD DC/DC 24V 400W
相關代理商/技術參數
參數描述
MC705E6CDWE 制造商:Freescale Semiconductor 功能描述:
MC705J1A 制造商:Freescale Semiconductor 功能描述:
MC705J1ACDWE 功能描述:8位微控制器 -MCU HCO5 CORE+1.2K RAM + EPR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705J1ACDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MC705JJ7CDWE 功能描述:8位微控制器 -MCU 705JJ7 224 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*