參數資料
型號： MC68L11K4FN1
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT MICROCONTROLLER
中文描述： 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PQCC84
封裝： PLASTIC, LCC-84
文件頁數： 24/80頁
文件大小： 420K
代理商： MC68L11K4FN1
MOTOROLA
24
M68HC11 K Series
MC6HC11KTS/D
LVPEN —Low Voltage Programming Protect Enable
If LVPEN = 1, programming of the EEPROM is enabled unless the LVPI circuit detects that V
DD
has
fallen below a safe operating voltage, thus setting the low voltage programming inhibit bit in PPROG
register (LVPI = 1).
0 = Low voltage programming protect for EEPROM disabled
1 = Low voltage programming protect for EEPROM enabled
BPRT4 —Block Protect Bit for Upper 128 Bytes of EEPROM
Refer to description for BPRT[3:0].
PTCON —Protect for CONFIG
0 = CONFIG register can be programmed or erased normally
1 = CONFIG register cannot be programmed or erased
BPRT[3:0] —Block Protect Bits for EEPROM
0 = Protection disabled
1 = Protection enabled
INIT2 can be written only once in normal modes, any time in special modes.
EE[3:0] —EEPROM Map Position
EEPROM is at $xD80–$xFFF, where x is the hexadecimal digit represented by EE[3:0].
Bits [3:0] —Not implemented
Always read zero
3.5 Configuration Control Register (CONFIG)
The CONFIG register is used to define several system functions. Although the CONFIG register is an
address within the register block, it is actually an EEPROM byte with the address of $x03F. CONFIG is
made up of EEPROM cells and static latches. The operation of the MCU is controlled directly by these
latches and not the actual EEPROM byte. When programming the CONFIG register, the EEPROM byte
is being accessed. When the CONFIG register is being read, the static latches are being accessed.
The CONFIG register can be read at any time. The value read is the one latched from the EEPROM
cells during the last reset sequence. A new value programmed into this register cannot be read until a
subsequent reset occurs. Unused bits always read as ones.
In normal modes (SMOD = 0), CONFIG bits can only be written using the EEPROM programming se-
quence, and are neither readable nor active until latched via the next reset. In special modes (SMOD =
1), CONFIG bits can be written at any time.
Bit Name
BPRT4
BPRT3
BPRT2
BPRT1
BPRT0
Block Protected
$xF80–$xFFF
$xE60–$xF7F
$xDE0–$xE5F
$xDA0–$xDDF
$xD80–$xD9F
Block Size
128 Bytes
288 Bytes
128 Bytes
64 Bytes
32 Bytes
INIT2
—EEPROM Mapping
$0037
Bit 7
6
5
4
3
2
1
Bit 0
EE3
EE2
EE1
EE0
0
0
0
0
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68L11K4FN3 8-BIT MICROCONTROLLER
MC68L11K4FU1 8-BIT MICROCONTROLLER
MC68L11K4FU3 8-BIT MICROCONTROLLER
MC68HC11K1VFN2 8-BIT MICROCONTROLLER
MC68HC11K1VFN3 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FU2 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68L711M2CFU 制造商:Freescale Semiconductor 功能描述:
MC68LC040FE20A 功能描述:微處理器 - MPU 32B W/ CACHE MMU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*