參數資料
型號: MC68HC705X4DWR2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 2.2 MHz, MICROCONTROLLER, PDSO28
封裝: PLASTIC, SOIC-28
文件頁數: 25/168頁
文件大?。?/td> 656K
代理商: MC68HC705X4DWR2
16-Bit Programmable Timer
MC68HC05X4 Rev 1.0
120
16-Bit Programmable Timer
MOTOROLA
location $17 will not inhibit the compare function. The processor can
write to either byte of the output compare register without affecting the
other byte. The output level (OLVL) bit is clocked to the output level
register whether the output compare flag (OCF) is set or clear. The
minimum time required to update the output compare register is a
function of the program rather than the internal hardware. Because the
output compare flag and the output compare register are not defined at
power on, and not affected by reset, care must be taken when initializing
output compare functions with software. The following procedure is
recommended:
1. write to output compare high to inhibit further compares;
2. read the timer status register to clear OCF (if set);
3. write to output compare low to enable the output compare
function.
All bits of the output compare register are readable and writable and are
not altered by the timer hardware or reset. If the compare function is not
needed, the two bytes of the output compare register can be used as
storage locations.
Timer during WAIT mode
All CPU action is suspended, but the timers (core and 16-bit) remain
active. An interrupt from either of the timers, if enabled, will cause the
MCU to exit WAIT mode.
Timer during STOP mode
In the STOP mode all MCU clocks are stopped, hence the timer stops
counting. If STOP is exited by an interrupt the counter retains the last
count value. If the device is reset, then the counter is forced to $FFFC.
During STOP, if at least one valid input capture edge occurs at the TCAP
pin, the input capture detect circuit is armed. This does not set any timer
flags nor wake up the MCU. When the MCU does wake up, however,
there is an active input capture flag and data from the first valid edge that
12-ptimer
相關PDF資料
PDF描述
MC68HC05X4CDWR2 8-BIT, MROM, 2.2 MHz, MICROCONTROLLER, PDSO28
MC68HC708KH12FU 8-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP64
MC68HC708LN56PV 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP144
MC68HC08LN56PV 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP144
MC68HC711E20CFNE 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC52
相關代理商/技術參數
參數描述
MC68HC706P6ACDW 制造商:Motorola Inc 功能描述:
MC68HC708MP16CFU 制造商:MAJOR 功能描述:
MC68HC711D3CFBE2 制造商:Freescale Semiconductor 功能描述:
MC68HC711D3CFN2 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711D3CFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT