參數資料
型號： MC68HC705C9AFB
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
封裝： 10 X 10 MM, QFP-44
文件頁數： 9/177頁
文件大?。?/td> 1941K
代理商： MC68HC705C9AFB
Serial Peripheral Interface (SPI)
Advance Information
MC68HC705C9A — Rev. 4.0
106
Serial Peripheral Interface (SPI)
MOTOROLA
10.4.3 Serial Clock (SCK)
The master clock is used to synchronize data movement both in and out
of the device through its MOSI and MISO lines. The master and slave
devices are capable of exchanging a byte of information during a
sequence of eight clock cycles. Since SCK is generated by the master
device, this line becomes an input on a slave device.
As shown in Figure 10-1, four possible timing relationships may be
chosen by using control bits CPOL and CPHA in the serial peripheral
control register (SPCR). Both master and slave devices must operate
with the same timing. The master device always places data on the
MOSI line a half cycle before the clock edge (SCK), in order for the slave
device to latch the data.
Two bits (SPR0 and SPR1) in the SPCR of the master device select the
clock rate. In a slave device, SPR0 and SPR1 have no effect on the
operation of the SPI.
10.4.4 Slave Select (SS)
The slave select (SS) input line is used to select a slave device. It has to
be low prior to data transactions and must stay low for the duration of the
transaction.The SS line on the master must be tied high. In master
mode, if the SS pin is pulled low during a transmission, a mode fault error
flag (MODF) is set in the SPSR. In master mode the SS pin can be
selected to be a general-purpose output (when configured as an
MC68HC05C9A) by writing a 1 in bit 5 of the port D data direction
register, thus disabling the mode fault circuit.
When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI
message. When CPHA = 1, SS may be left low for several SPI
characters. In cases where there is only one SPI slave MCU, its SS line
could be tied to VSS as long as CPHA = 1 clock modes are used.
相關PDF資料
PDF描述
MC68HC705C9AVFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC705C9AP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP40
MC68HC705C9AFB 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68LNC705C9ACFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC705C9ACS 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC705C9AFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC705C9AVFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC705E6CDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC705G1B 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705J1A 制造商:Freescale Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*