- 您現在的位置：買賣IC網 > PDF目錄45228 > MC68HC11E9BCFU2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MC68HC11E9BCFU2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | QFP-64 |
| 文件頁數： | 136/242頁 |
| 文件大?。?/td> | 1672K |
| 代理商： | MC68HC11E9BCFU2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁當前第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁
M68HC11 Bootstrap Mode, Rev. 1.1
220
Freescale Semiconductor
Common Bootstrap Mode Problems
Connecting RxD to VSS Does Not Cause the SCI to Receive a Break
To force an immediate jump to the start of EEPROM, the bootstrap firmware looks for the first received
character to be $00 (or break). The data reception logic in the SCI looks for a 1-to-0 transition on the RxD
pin to synchronize to the beginning of a receive character. If the RxD pin is tied to ground, no 1-to-0
transition occurs. The SCI transmitter sends a break character when the bootloader firmware starts, and
this break character can be fed back to the RxD pin to cause the jump to EEPROM. Since TxD is
configured as an open-drain output, a pullup resistor is required.
$FF Character Is Required before Loading into RAM
The initial character (usually $FF) that sets the download baud rate is often forgotten.
Original M68HC11 Versions Required Exactly 256 Bytes to be Downloaded to RAM
Even users that know about the 256 bytes of download data sometimes forget the initial $FF that makes
the total number of bytes required for the entire download operation equal to 256 + 1 or 257 bytes.
Variable-Length Download
When on-chip RAM surpassed 256 bytes, the time required to serially load this many characters became
more significant. The variable-length download feature allows shorter programs to be loaded without
sacrificing compatibility with earlier fixed-length download versions of the bootloader. The end of a
download is indicated by an idle RxD line for at least four character times. If a personal computer is being
used to send the download data to the MCU, there can be problems keeping characters close enough
together to avoid tripping the end-of-download detect mechanism. Using 1200 as the baud rate rather
than the faster default rate may help this problem.
Assemblers often produce S-record encoded programs which must be converted to binary before
bootloading them to the MCU. The process of reading S-record data from a file and translating it to binary
can be slow, depending on the personal computer and the programming language used for the
translation. One strategy that can be used to overcome this problem is to translate the file into binary and
store it into a RAM array before starting the download process. Data can then be read and downloaded
without the translation or file-read delays.
The end-of-download mechanism goes into effect when the initial $FF is received to set the baud rate.
Any amount of time may pass between reset and when the $FF is sent to start the download process.
EPROM/OTP Versions of M68HC11 Have an EPROM Emulation Mode
The conditions that configure the MCU for EPROM emulation mode are essentially the same as those for
resetting the MCU in bootstrap mode. While RESET is low and mode select pins are configured for
bootstrap mode (low), the MCU is configured for EPROM emulation mode.
The port pins that are used for EPROM data I/O lines may be inputs or outputs, depending on the pin that
is emulating the EPROM output enable pin (OE). To make these data pins appear as high-impedance
inputs as they would on a non-EPROM part in reset, connect the PB7/(OE) pin to a pullup resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11E9BCPB3 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP52 |
| MC68HC711E20VFS2 | 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQCC52 |
| MC68HC11E9FN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC11E9FNR2 | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC11E9MFN1R2 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11E9BCFU3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-channel, 8-bit analog-to-digital (A/D) converter |
| MC68HC11E9BCPB2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC11E9BCPB3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC11E9CB2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC11E9CB3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-channel, 8-bit analog-to-digital (A/D) converter |
發布緊急采購，3分鐘左右您將得到回復。