參數資料
型號: MC68HC11D0CFB2
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 114/138頁
文件大?。?/td> 1047K
代理商: MC68HC11D0CFB2
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
77
Chapter 7
Serial Peripheral Interface (SPI)
7.1 Introduction
The serial peripheral interface (SPI), an independent serial communications subsystem, allows the
microcontroller unit (MCU) to communicate synchronously with peripheral devices, such as:
Transistor-transistor logic (TTL) shift registers
Liquid crystal diode (LCD) display drivers
Analog-to-digital converter (ADC) subsystems
Other microprocessors (MCUs)
The SPI is also capable of inter-processor communication in a multiple master system. The SPI system
can be configured as either a master or a slave device with data rates as high as one half of the E-clock
rate when configured as master, and as fast as the E-clock rate when configured as slave.
7.2 Functional Description
The central element in the SPI system is the block containing the shift register and the read data buffer.
The system is single buffered in the transmit direction and double buffered in the receive direction. This
means that new data for transmission cannot be written to the shifter until the previous transfer is
complete; however, received data is transferred into a parallel read data buffer so the shifter is free to
accept a second serial character. As long as the first character is read out of the read data buffer before
the next serial character is ready to be transferred, no overrun condition occurs. A single MCU register
address is used for reading data from the read data buffer, and for writing data to the shifter.
The SPI status block represents the SPI status functions (transfer complete, write collision, and mode
fault) performed by the serial peripheral status register (SPSR). The SPI control block represents those
functions that control the SPI system through the serial peripheral control register (SPCR).
Refer to Figure 7-1, which shows the SPI block diagram.
7.3 SPI Transfer Formats
During an SPI transfer, data is simultaneously transmitted and received. A serial clock line synchronizes
shifting and sampling of the information on the two serial data lines. A slave select line allows individual
selection of a slave SPI device; slave devices that are not selected do not interfere with SPI bus activities.
On a master SPI device, the select line can optionally be used to indicate a multiple master bus
contention. Refer to Figure 7-2.
相關PDF資料
PDF描述
MC68HC11D3CFN2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44
MC68HC711D3CP3 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP40
MC68HC11D3CFN3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44
MC68HC11D3CFB1 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44
MC68L11D0CFB3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68HC11D0CFB3 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC11D0CFB3R2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC11D0CFBE2 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFBE3 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11D0CFBE3R 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT