參數資料
型號: MC68HC11A1CFN2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: HCMOS Single-Chip Microcontroller
中文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52
封裝: PLASTIC, LCC-52
文件頁數: 33/158頁
文件大?。?/td> 776K
代理商: MC68HC11A1CFN2
MC68HC11A8
TECHNICAL DATA
ON-CHIP MEMORY
MOTOROLA
3-7
3
EELAT — EEPROM Latch Control
0 = EEPROM Address and Data Configured for Read Mode
1 = EEPROM Address and Data Configured for Programming/Erasing
EEPGM — EEPROM Programming Voltage Enable
0 = Programming Voltage Switched Off
1 = Programming Voltage Turned On
If an attempt is made to set both the EELAT and EEPGM bits in the same write cycle,
neither will be set. If a write to an EEPROM address is performed while the EEPGM
bit is set, the write is ignored and the programming operation currently in progress is
not disturbed. These two safeguards were included to prevent accidental EEPROM
changes in cases of program runaway. Mask sets A38P, A49N, and date codes before
86xx did not have these safeguards.
3.5.2 Programming/Erasing Internal EEPROM
The EEPROM programming and erasure process is controlled by the PPROG regis-
ter. The following paragraphs describe the various operations performed on the EE-
PROM and include example program segments to demonstrate programming and
erase operations.
These program segments are intended to be simple straightforward examples of the
sequences needed for basic program and erase operations. There are no special re-
strictions on the address modes used and bit manipulation instructions may be used.
Other MCU operations can continue to be performed during EEPROM programming
and erasure provided these operations do not include reads of data from EEPROM
(the EEPROM is disconnected from the read data bus during EEPROM program and
erase operations). The subroutine DLY10 used in these program segments is not
shown but can be any set of instructions which takes ten milliseconds.
3.5.2.1 Read
For the read operation the EELAT bit in the PPROG register must be clear. When this
bit is cleared, the remaining bits in the PPROG register have no meaning or effect, and
the EEPROM may be read as if it were a normal ROM.
3.5.2.2 Programming
During EEPROM programming, the ROW and BYTE bits are not used. If the E clock
frequency is 1 MHz or less, the CSEL bit in the OPTION register must be set. Recall
that in this EEPROM, zeros must be erased by a separate erase operation before pro-
gramming. The following program segment demonstrates how to program an EE-
PROM byte.
相關PDF資料
PDF描述
MC68HCP11A1CFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CFN3 HCMOS Single-Chip Microcontroller
MC68HCP11A1CP2 HCMOS Single-Chip Microcontroller
MC68HCP11A1CP3 HCMOS Single-Chip Microcontroller
MC68HCP11A1MFN2 HCMOS Single-Chip Microcontroller
相關代理商/技術參數
參數描述
MC68HC11A1CFN3 制造商:Rochester Electronics LLC 功能描述:
MC68HC11A1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFNE3 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC
MC68HC11A1CFNE3R 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller