- 您現在的位置：買賣IC網 > PDF目錄371043 > MC68332MFC20 (MOTOROLA INC) 32-Bit Modular Microcontroller PDF資料下載
參數資料
| 型號： | MC68332MFC20 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-Bit Modular Microcontroller |
| 中文描述： | 32-BIT, 20 MHz, MICROCONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 53/88頁 |
| 文件大小： | 446K |
| 代理商： | MC68332MFC20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
MC68332
MC68332TS/D
MOTOROLA
53
5.1.2 Input Capture/Input Transition Counter (ITC)
Any channel of the TPU can capture the value of a specified TCR upon the occurrence of each transition
or specified number of transitions, and then generate an interrupt request to notify the CPU. A channel
can perform input captures continually, or a channel can detect a single transition or specified number
of transitions, then cease channel activity until reinitialization. After each transition or specified number
of transitions, the channel can generate a link to a sequential block of up to eight channels. The user
specifies a starting channel of the block and the number of channels within the block. The generation
of links depends on the mode of operation. In addition, after each transition or specified number of tran-
sitions, one byte of the parameter RAM (at an address specified by channel parameter) can be incre-
mented and used as a flag to notify another channel of a transition.
5.1.3 Output Compare (OC)
The output compare function generates a rising edge, falling edge, or a toggle of the previous edge in
one of three ways:
1.
Immediately upon CPU initiation, thereby generating a pulse with a length equal to a program-
mable delay time.
At a programmable delay time from a user-specified time.
Continuously. Upon receiving a link from a channel, OC references, without CPU interaction, a
specifiable period and calculates an offset:
Offset = Period
Ratio
2.
3.
where Ratio is a parameter supplied by the user.
This algorithm generates a 50% duty-cycle continuous square wave with each high/low time equal to
the calculated OFFSET. Due to offset calculation, there is an initial link time before continuous pulse
generation begins.
5.1.4 Pulse-Width Modulation (PWM)
The TPU can generate a pulse-width modulation waveform with any duty cycle from zero to 100% (with-
in the resolution and latency capability of the TPU). To define the PWM, the CPU provides one param-
eter that indicates the period and another parameter that indicates the high time. Updates to one or both
of these parameters can direct the waveform change to take effect immediately, or coherently beginning
at the next low-to-high transition of the pin.
5.1.5 Synchronized Pulse-Width Modulation (SPWM)
The TPU generates a PWM waveform in which the CPU can change the period and/or high time at any
time. When synchronized to a time function on a second channel, the synchronized PWM low-to-high
transitions have a time relationship to transitions on the second channel.
5.1.6 Period Measurement with Additional Transition Detect (PMA)
This function and the following function are used primarily in toothed-wheel speed-sensing applications,
such as monitoring rotational speed of an engine. The period measurement with additional transition
detect function allows for a special-purpose 23-bit period measurement. It can detect the occurrence of
an additional transition (caused by an extra tooth on the sensed wheel) indicated by a period measure-
ment that is less than a programmable ratio of the previous period measurement.
Once detected, this condition can be counted and compared to a programmable number of additional
transitions detected before TCR2 is reset to $FFFF. Alternatively, a byte at an address specified by a
channel parameter can be read and used as a flag. A nonzero value of the flag indicates that TCR2 is
to be reset to $FFFF once the next additional transition is detected.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68332TS | 32-Bit Modular Microcontroller |
| MC68332GCFC16 | 32-Bit Modular Microcontroller |
| MC68332GCFC20 | 32-Bit Modular Microcontroller |
| MC68332GCFV20 | 32-Bit Modular Microcontroller |
| MC68332GCFVV16 | 32-Bit Modular Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68332MFV16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332MFV20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332TS | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332VFC16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332VFC20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。