參數資料
型號： MC56F8013MFAE
廠商： Freescale Semiconductor
文件頁數： 112/126頁
文件大?。?/td> 0K
描述： IC DIGITAL SIGNAL CTLR 32-LQFP
標準包裝： 1,250
系列： 56F8xxx
核心處理器： 56800E
芯體尺寸： 16-位
速度： 32MHz
連通性： I²C，SCI，SPI
外圍設備： POR，PWM，WDT
輸入/輸出數： 26
程序存儲器容量： 16KB（8K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 16
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 6x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 32-LQFP
包裝： 托盤
56F8013/56F8011 Data Sheet, Rev. 12
86
Freescale Semiconductor
7.2.4
Flash Lockout Recovery Without Mass Erase
The user can un-secure a secured device by programming the word $0000 into program memory location
$00 1FF7. After completing the programming, both the JTAG TAP controller and the device must be
reset in order to return to normal unsecured operation. Power-on reset will also reset both.
The user is responsible for directing the device to invoke the flash programming subroutine to reprogram
the word $0000 into program memory location $00 1FF7. This is done by, for example, toggling a specific
pin, or by downloading a user-defined key through serial interfaces.
Note:
Flash contents can only be programmed for 1s to 0s.
7.3 Product Analysis
The recommended method of unsecuring a secured device for product analysis of field failures is via the
method suggested in Section 7.2.4. The customer would need to supply Technical Support with the details
of the protocol to access the subroutines in flash. An alternative method for performing analysis on a
secured device would be to mass-erase and reprogram the flash with the original code, but also either
modify the security word or else not program the security word.
Part 8 General Purpose Input/Output (GPIO)
8.1 Introduction
This section is intended to supplement the GPIO information found in the 56F801X Peripheral User
Manual and contains only chip-specific information. This information supercedes the generic information
in the 56F801X Peripheral User Manual.
8.2 Configuration
There are four GPIO ports defined on the 56F8013/56F8011. The width of each port, the associated
peripheral and reset functions are shown in Table 8-1. The specific mapping of GPIO port pins is shown
相關PDF資料
PDF描述
VI-B7M-IY-F4 CONVERTER MOD DC/DC 10V 50W
VI-BVT-IY-F4 CONVERTER MOD DC/DC 6.5V 50W
VE-B6D-IY-B1 CONVERTER MOD DC/DC 85V 50W
VI-BVT-IY-F2 CONVERTER MOD DC/DC 6.5V 50W
VI-BVT-IY-F1 CONVERTER MOD DC/DC 6.5V 50W
相關代理商/技術參數
參數描述
MC56F8013MFAER2 制造商:Freescale Semiconductor 功能描述:16 BIT DSPHC ANGUILLA - Tape and Reel
MC56F8013PB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
MC56F8013VFAE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT DSPHC ANGUILLA RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8013VFAER2 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT DSPHC ANGUILLA RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8014 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*