- 您現在的位置：買賣IC網 > PDF目錄11725 > MC33993DWB (Freescale Semiconductor)IC SWITCH I/O INTERFACE 32-SOIC PDF資料下載
參數資料
| 型號： | MC33993DWB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH I/O INTERFACE 32-SOIC |
| 標準包裝： | 42 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
33993
TYPICAL APPLICATIONS
INTRODUCTION
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
from first device is connected to SI of second device). With
two devices, 48 clock pulses are required to shift data in.
When the WAKE feature is used to enable the power supply,
both WAKE pins should be connected to the enable pin on
the power supply. The INT pins may be connected to one
interrupt pin on the MCU or may have their own dedicated
interrupt to the MCU.
The transition from Normal to Sleep mode is done by
sending the sleep command. With the devices connected in
serial and the sleep command sent, both will enter Sleep
mode on the rising edge of CS. When Sleep mode is entered,
the WAKE pin will be logic [1]. If either device wakes up, the
WAKE pin will transition low, waking the other device.
A condition exists where the MCU is sending the sleep
command (CS logic [0]) and a switch input changes state.
With this event the device that detects this input will not
transition to Sleep mode, while the second device will enter
Sleep mode. In this case two switch status commands must
be sent to receive accurate switch status data. The first
switch status command will wake the device in Sleep mode.
Switch status data may not be valid from the first switch
status command because of the time required for the input
voltage to rise above the 4.0 V input comparator threshold.
This time is dependant on the impedance of SGn or SPn
node. The second switch status command will provide
accurate switch status information. It is recommended that
software wait 10 ms to 20 ms between the two switch status
commands, allowing time for switch input voltages to
stabilize. With all switch states acknowledged by the MCU,
the sleep sequence may be initiated. All parameters for Sleep
mode should be updated prior to sending the sleep
command.
The 33993 IC has an internal 5.0 V supply from VPWR pin.
A POR circuit monitors the internal 5.0 V supply. In the event
of transients on the VPWR pin, an internal reset may occur.
Upon reset the 33993 will enter Normal mode with the
internal registers as defined in Table 14, page 16. Therefore
it is recommended that the MCU periodically update all
registers internal to the IC.
USING THE WAKE FEATURE
The 33993 provides a WAKE output and wake-up input
designed to control an enable pin on system power supply.
While in the Normal mode, the WAKE output is low, enabling
the power supply. In the Sleep mode, the WAKE pin is high,
disabling the power supply. The WAKE pin has a passive
pull-up to the internal 5.0 V supply but may be pulled up
When the WAKE output is not used the pin should be
pulled up to the VDD supply through a resistor as shown in
During the Sleep mode, a switch closure will set the WAKE
pin low, causing the 33993 to enter the Normal mode. The
power supply will then be activated, supplying power to the
VDD pin and the microprocessor and the 33993. The
microprocessor can determine the source of the wake-up by
reading the interrupt flag.
COST AND FLEXIBILITY
Systems requiring a significant number of switch
interfaces have many discrete components. Discrete
components on standard PWB consume board space and
must be checked for solder joint integrity. An integrated
approach reduces solder joints, consumes less board space,
and offers wider operating voltage, analog interface
capability, and greater interfacing flexibility.
相關PDF資料 |
PDF描述 |
|---|---|
| 31-203-RFX | PANEL JACK - SOLDER - 50 OHM |
| MC33884DW | IC SWITCH SDI MONITOR 24-SOIC |
| D38999/26MB99PA | CONN PLUG 7POS STRAIGHT W/PINS |
| MC33399D | IC LIN INTERFACE W/WAKE 8-SOIC |
| ATTINY88-AU | MCU AVR 8K ISP FLASH 1.8V 32TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33993DWBR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33996EK | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33996EKR2 | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33997DW | 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| MC33997DWR2 | 制造商:Rochester Electronics LLC 功能描述:MLPS 3.3 IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。