- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33991 (飛思卡爾半導體(中國)有限公司) Gauge Driver Integrated Circuit(標尺驅動器集成電路) PDF資料下載
參數資料
| 型號： | MC33991 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Gauge Driver Integrated Circuit(標尺驅動器集成電路) |
| 中文描述： | 儀表驅動集成電路（標尺驅動器集成電路） |
| 文件頁數： | 20/36頁 |
| 文件大?。?/td> | 660K |
| 代理商： | MC33991 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
33991
20
Go to: www.freescale.com
ST0–Gauge0—Junctionovertemperature.Alogic[1]onthis
bit indicates coil drive circuitry dedicated to drive Gauge 0 has
exceeded the maximum allowable junction temperature since
the last SPI communication. Additionally, the same indication
signals the circuitry Gauge 0 is disabled. It is recommended the
pointer be re-calibrated using the RTZ command after re-
enabling the gauge, using the PECR command. This bit
remains logic [1] until the gauge is re-enabled.
0 = Temperature within range
1 = Gauge 0 maximum allowable junction temperature
condition has been reached
DEVICE FUNCTIONAL DESCRIPTION
State Machine Operation
The two-phase stepper motor is defined as maximum
velocity and acceleration, and deceleration. It is the purpose of
the stepper motor state machine to drive the motor with
maximum performance while remaining within the motor’s
velocity and acceleration constraints.
When commanded, the motor should accelerate constantly
to its maximum velocity then decelerate and stop at the desired
position. During the deceleration phase, the motor should not
exceed the maximum deceleration. A required function of the
state
machine is to ensure the deceleration phase begins at the
correct time, or position.
During normal operation, both stepper motor rotors are
microsteppedwith24stepsper electricalrevolution. See Figure
6. A complete electrical revolution results in 2 degrees of
pointer movement. There is a second, and smaller state,
machine in the IC controlling these microsteps. This state
machine receives
clockwise
or
counter-clockwise
index
commands at intervals, stepping the motor in the appropriate
direction by adjusting the current in each coil. Normalized
values can be seen in Table 13.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33993 | Multiple Switch Detection Interface(多開關監測接口) |
| MC33997 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC33998 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC34017 | Telephone Tone Ringer(電話振鈴) |
| MC34063A | DC-DC CONVERTER CONTROL CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
| MC33991DWR2 | 制造商:Rochester Electronics LLC 功能描述:GUAGE DRIVER IC - Bulk |
| MC33993DWB | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33993DWBR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33996EK | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。