- 您現在的位置：買賣IC網 > PDF目錄11717 > MC33972TEW (Freescale Semiconductor)IC SWITCH DETECT SPI 32-SOIC PDF資料下載
參數資料
| 型號： | MC33972TEW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 15/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DETECT SPI 32-SOIC |
| 標準包裝： | 42 |
| 應用： | 開關監控 |
| 接口： | SPI 串行 |
| 電源電壓： | 3.1 V ~ 5.25 V |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33972
TYPICAL APPLICATIONS
INTRODUCTION
Figure 14. Analog Ratiometric Conversion
To read a potentiometer sensor, the wiper should be
grounded and brought back to the module ground, as
illustrated in Figure 14. With the wiper changing the
impedance of the sensor, the analog voltage on the input will
represent the position of the sensor.
Using the Analog feature to provide 2.0 mA of pull-up
current to an analog sensor may induce error due to the
accuracy of the current source. For this reason, a ratiometric
conversion must be considered. Using two current sources
(one for the sensor and one to set the reference voltage to the
A/D converter) will yield a maximum error (owing to the
33972) of 4%.
Higher accuracy may be achieved through module level
calibration. In this example, we use the resistor values from
Figure 14 and assume the current sources are 4% from each
other. The user may use the module end-of-line tester to
calculate the error in the A/D conversion. By placing a
2.0 k
Ω, 0.1% resistor in the end-of-line test equipment and
assuming a perfect 2.0 mA current source from the 33972, a
calculated A/D conversion may be obtained. Using the
equation yields the following:
The ADC value of 213 counts is the value with 0% error
(neglecting the resistor tolerance and AMUX input offset
voltage). Now we can calculate the count value induced by
the mismatch in current sources. From a sample device the
maximum current source was measured at 2.05 mA and
minimum current source was measured at 1.99 mA. This
yields 3% error in A/D conversion. The A/D measurement
will be as follows:
This A/D conversion is 3% low in value. The error
correction factor of 1.03 may be used to correct the value:
An error correction factor may then be stored in E2
memory and used in the A/D calculation for the specific input.
Each input used as analog measurement will have a
dedicated calibrated error correction factor.
POWER MOSFET/LED DRIVER AND MONITOR
Because of the flexible programming of the 33972 device,
it may be used to drive small loads like LEDs or MOSFET
gates. It was specifically designed to power up in the Normal
mode with the inputs tri-state. This was done to ensure the
LEDs or MOSFETs connected to the 33972 power up in the
off-state. The switch programmable inputs (SP0–SP7) have
a source-and-sink capability, providing effective MOSFET
gate control. To complete the circuit, a pull-down resistor
should be used to keep the gate from floating during the
where the SG0 input is used to monitor the drain-to-source
voltage of the external MOSFET. The 1.5 k
Ω resistor is used
to set the drain-to-source trip voltage. With the 2.0 mA
current source enabled, an interrupt will be generated when
the drain-to-source voltage is approximately 1.0 V.
VDD
VPWR
VDD
SI
SO
SCLK
INT
CS
AMUX
MOSI
MISO
AN0
VBAT
SP0
SP1
SP7
SG1
SG0
SG12
SG13
WAKE
VBAT
SCLK
CS
INT
16
2.0
VPWR
2.0mA
2.39k
Ω
0.1%
4.54V to 5.02V
Analog
Ports
VREF(H)
VREF(L)
Analog Sensor
or Analog Switch
R2
I2
I1
R1
VPWR
mA
2.0
VPWR
mA
16
mA
33972
MCU
ADC =
I1 x R1
I2 x R2
x 255
ADC =
2.0mA x 2.0k
Ω
x 255
2.0mA x 2.39k
Ω
ADC = 213 counts
ADC =
1.99mA x 2.0k
Ω
x255
2.05mA x 2.39k
Ω
ADC = 207 counts
ADC = 207 counts x 1.03
ADC = 213 counts
相關PDF資料 |
PDF描述 |
|---|---|
| V150A28E500B | CONVERTER MOD DC/DC 28V 500W |
| MS3101A36-1P | CONN RCPT 22POS FREE HNG W/PINS |
| VE-B0H-IX-F3 | CONVERTER MOD DC/DC 52V 75W |
| MS3126F16-26PY | CONN PLUG 26POS STRAIGHT W/PINS |
| V150A24E500BL3 | CONVERTER MOD DC/DC 24V 500W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33972TEWR2 | 功能描述:接口 - 專用 MULTI-SW DETECT W/SUPRES RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33975ATEK | 功能描述:接口 - 專用 ENHANCED MULTI SW DETECT RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33975ATEKR2 | 功能描述:接口 - 專用 ENHANCED MULTI SW DETECT RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33975EK | 功能描述:多路器開關 IC EMSDI RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC33975EKR2 | 功能描述:多路器開關 IC EMSDI RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。