- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33887 (飛思卡爾半導體(中國)有限公司) 5.0 A H-Bridge with Load Current Feedback(帶本地電流反饋功能的5.0A H橋接器) PDF資料下載
參數資料
| 型號： | MC33887 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 5.0 A H-Bridge with Load Current Feedback(帶本地電流反饋功能的5.0A H橋接器) |
| 中文描述： | 5.0的H -橋的負載電流反饋（帶本地電流反饋功能的5.0AH橋接器） |
| 文件頁數： | 20/28頁 |
| 文件大小： | 760K |
| 代理商： | MC33887 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
33887
20
Go to: www.freescale.com
PERFORMANCE FEATURES
Short Circuit Protection
If an output short circuit condition is detected, the power
outputs tri-state (latch-OFF) independent of the input (IN1 and
IN2) states, and the fault status output flag is SET logic LOW. If
the D1 input changes from logic HIGH to logic LOW, or if the
D2
input changes from logic LOW to logic HIGH, the output bridge
will become operational again and the fault status flag will be
reset (cleared) to a logic HIGH state.
The output stage will always switch into the mode defined by
the input terminals (IN1, IN2, D1, and
D2
), provided the device
junction temperature is within the specified operating
temperature range.
Active Current Limiting
The maximum current flow under normal operating
conditions is internally limited to I
LIM
(5.2 A to 7.8 A). When the
maximum current value is reached, the output stages are tri-
stated for a fixed time (t
a
) of 20
μ
s typical. Depending on the
time constant associated with the load characteristics, the
current decreases during the tri-state duration until the next
output ON cycle occurs (see
Figures 7
and
13
, page 12 and
page 15, respectively).
The current limiting threshold value is dependent upon the
device junction temperature. When -40
°
C
≤
T
J
≤
160
°
C, I
LIM
is
between 5.2 A to 7.8 A. When T
J
exceeds 160
°
C, the
I
LIM
current decreases linearly down to 4.0 A typical at 175
°
C.
Above 175
°
C the device overtemperature circuit detects T
LIM
and overtemperature shutdown occurs (see
Figure 5
, page 11).
This feature allows the device to remain operational for a longer
time but at a regressing output performance level at junction
temperatures above 160
°
C.
Overtemperature Shutdown and Hysteresis
If an overtemperature condition occurs, the power outputs
are tri-stated (latched-OFF) and the fault status flag is SET to
logic LOW.
To reset from this condition, D1 must change from logic
HIGH to logic LOW, or
D2
must change from logic LOW to logic
HIGH. When reset, the output stage switches ON again,
provided that the junction temperature is now below the
overtemperature threshold limit minus the hysteresis.
Note
Resetting from the fault condition will clear the fault
status flag.
PACKAGE INFORMATION
The 33887 is designed for enhanced thermal performance.
The significant feature of this device is the exposed copper pad
on which the power die is soldered. This pad is soldered on a
PCB to provide heat flow to ambient and also to provide thermal
capacitance. The more copper area on the PCB, the better the
power dissipation and transient behavior will be.
Example
Characterization on a double-sided PCB: bottom
side area of copper is 7.8 cm
2
; top surface is 2.7 cm
2
(see
Figure 19
); grid array of 24 vias 0.3 mm in diameter.
Figure 19. PCB Test Layout
Figure 20
shows the thermal response with the device
soldered on to the test PCB described in
Figure 19
.
Figure 20. 33887 Thermal Response
Top Side
Bottom Side
0,1
0,001
1
10
100
0,01
0,1
1
10
100
1000
10000
t, Time (s)
Rth (°C/W)
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33888FB | Quad High Side and Octal Low Side Switch for Automotive Applications(4高端開關及8低端開關，用于自動應用) |
| MC33889 | System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface |
| MC33897 | Single-Wire CAN Transceiver(單線CAN收發器) |
| MC33972 | Multiple Switch Detection Interface with Suppressed Wake-Up(帶抑制喚醒功能的多開關檢測接口) |
| MC33976 | Dual Gauge Driver with Configurable Response Time(帶可設置響應時間的雙標尺驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33887APVW | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33887APVW-PB | 制造商:Freescale Semiconductor 功能描述: |
| MC33887APVWR2 | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33887AVW | 功能描述:開關 IC - 各種 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel |
| MC33887AVWR2 | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。