參數資料
型號： MC33884DW
廠商： Freescale Semiconductor
文件頁數： 2/21頁
文件大?。?/td> 0K
描述： IC SWITCH SDI MONITOR 24-SOIC
標準包裝： 30
系列： *
應用： *
接口： *
電源電壓： *
封裝/外殼： 24-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 24-SOIC
包裝： 管件
安裝類型： 表面貼裝
Analog Integrated Circuit Device Data
10
Freescale Semiconductor
33884
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
Figure 5. SPI Parallel Interface with Microprocessor
Figure 6. SPI Serial Interface with Microprocessor
FUNCTIONAL PIN DESCRIPTION
CHIP SELECT (CS)
The MCU system selects the 33884 to receive its
communication through the Chip Select (CS) pin. With the CS
in a logic low state, command words may be sent to the
33884 via the Serial Input (SI) pin. Switch status is received
by the MCU via Serial Output (SO) pin. The falling edge of CS
enables the SO output, latches the state of the Interrupt (INT)
pin, Operating mode and the state of the external switch
inputs. The rising edge of CS disables the SO driver, resets
the INT pin to logic [1], activates the received command word,
and allows the 33884 to act upon new data obtained from
switch inputs. To avoid any spurious data, it is essential the
high-to-low and low-to-high transition of the CS signal occur
only when System Clock (SCLK) is in a logic low state.
Internal to the 33884 is an active pull-up on CS pin.
SYSTEM CLOCK (SCLK)
The System Clock (SCLK) pin clocks the internal 16-bit
Shift register. The Serial Input (SI) data is latched into the
Input Shift register on the rising edge of SCLK signal. The
Serial Output (SO) pin shifts the switch status bits out on the
falling edge of SCLK. False clocking of the Shift register must
be avoided to guarantee validity of data. It is essential the
SCLK pin be in a logic low state whenever CS makes any
transition. For this reason it is recommended, though not
necessary, the SCLK pin be commanded to a low logic state
as long as the device is not accessed (CS in logic high state).
When the CS is in a logic high state, any signal on the SCLK
and SI pin will be ignored and the SO pin is Tri-Stated (high
impedance).
SERIAL INPUT (SI)
This Serial Input (SI) pin is used for serial instruction data
input. SI information is latched into the Input register on the
rising edge of SCLK. A logic high state present at SI when
SCLK rises, programs a logic [1] into the command word on
rising edge of the CS signal. To program a complete word, 16
bits of information must be entered into the 33884. Internal to
the IC is an active pull down on the SI pin.
SERIAL OUTPUT (SO)
The Serial Output (SO) pin is the output from the Shift
register. The SO pin remains Tri-Stated until the CS pin
transitions to a logic low state. All open switches are reported
as logic [0], all closed switches are reported as logic [1]. The
negative transition of CS will make status bit 15 available on
SO. Each successive negative clock makes the next status
bit available. The SI/SO shifting of the data follows a first-in-
first-out protocol with both input and output words transferring
the most significant bit (MSB) first.
MASTER/SLAVE (MASL)
The Master/Slave (MASL) pin is required when multiple
33884 devices are used in one module. The MASL identifies
which device will be the master or slave. MASL identification
is used during the Polling mode. In the Polling mode, the
master device has it’s internal oscillator running while the
Slave device oscillator is shutdown. While polling, the master
device wakes the slave via the Synchronization (SYNC) pin.
This feature provides minimal quiescent from the voltage
power (VPWR) and voltage digital drain (VDD) pins.
MC68HCXX
Microcontroller
33884
MOSI
16 Bit Shift Register
MISO
Parallel
Ports
SCLK
INT
SI
SO
SCLK
CS
RST
INT
Microcontroller
33884
MC68HCXX
16 Bit Shift Register
Parallel
Ports
INT
SCLK
MISO
MOSI
SI
SO
SCLK
CS
RST
INT
相關PDF資料
PDF描述
D38999/26MB99PA CONN PLUG 7POS STRAIGHT W/PINS
MC33399D IC LIN INTERFACE W/WAKE 8-SOIC
ATTINY88-AU MCU AVR 8K ISP FLASH 1.8V 32TQFP
MS27497E22B55S CONN RCPT 55POS WALL MNT W/SCKT
ATTINY48-MMH MCU AVR 4KB FLASH 12MHZ 28-VQFN
相關代理商/技術參數
參數描述
MC33886DH 功能描述:IC H-BRIDGE 5.0A OUTPUT 20-HSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR
MC33886DHR2 功能描述:IC H-BRIDGE 5.0A 20-HSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR
MC33886PVW 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33886PVWR2 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33886VW 功能描述:馬達/運動/點火控制器和驅動器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*