參數資料
型號： MC33291
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關)
中文描述： 8個串行外圍接口的I / O（帶的SPI接口的八輸出開關輸出開關）
文件頁數： 21/24頁
文件大?。?/td> 633K
代理商： MC33291
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33291
21
limiting output current is in effect and the output is permitted to
operate if the over current condition does not drive output into
an over temperature fault. An over temperature fault will
shutdown the specific output effected for the duration of the
over temperature condition.
Over current and over temperature faults are often related.
Turning the effected output switches OFF and waiting for some
time to allow the output to cool down should make these types
of faults go away.
Soft
over current faults can sometimes be
determined over hard short faults and over temperature faults
by observing the time required for the device to recover.
However, in general over current and over temperature faults
can not be differentiated in normal application usage.
An advantage of the synchronous serial output is multiple
faults can be detected with only one (SO) pin being used for
fault status reporting.
If V
PWR
experiences an over voltage condition, all outputs
will immediately be turned OFF and remain latched off. A new
command word is required to turn the outputs back on following
an over voltage condition.
Output Voltage Clamping
Each output of the 33291 incorporates an internal voltage
clamp to provide fast turn-off and transient protection of the
output. Each clamp independently limits the drain to source
voltage to 53 V at drain currents of 0.5 A and keeps the output
transistors from avalanching by causing the transient energy to
be dissipated in the linear mode. See Figure 19. The total
energy clamped (E
J
) can be calculated by multiplying the
current area under the current curve (I
A
) times the clamp
voltage (V
CL
) times the duration the clamp is active (t).
Characterization of the output clamps, using a single pulse
non-repetitive method at 0.5 A, indicate the maximum energy to
be 50 mJ at 150
°
C junction temperature per output. See Figure
19.
Figure 19. Output Voltage Clamping
THERMAL CHARACTERIZATION
Thermal Model
Logic functions take up a very small area of the die and
generate negligible power. In contrast, the output transistors
take up most of the die area and are the primary contributors of
power generation. The thermal model illustrated in Figure 20
was developed for the 33291 mounted on a typical PC board.
The model is accurate for both steady state and transient
thermal conditions. The components R
D0
through R
D7
represent
the steady state thermal resistance of the silicon die for
transistor outputs 0 through 7, while C
D0
through C
D7
represent
the corresponding thermal capacitance of the silicone die
translator outputs and plastic. The device area and die
thickness determine the values of these specific components.
The thermal impedance of the package from the internal
mounting flag to the outside environment is represented by the
terms R
pkg
and C
pkg
. The steady state thermal resistance of
leads and the PC board make up the steady state package
thermal resistance, R
pkg
. The thermal capacitance of the
package is made up of the combined capacitance of the flag
and the PC board. The mode compound was not modeled as a
specific component but it is factored into the other overall
component values.
The battery voltage in the thermal model represents the
ambient temperature the device and PC board are subjected to.
The I
PWR
current source represents the total power dissipation
and is calculated by totalling the power dissipation of each
individual output transistor. This is easily accomplished by
knowing R
DS(on)
and load current of the individual outputs.
Very satisfactory steady state and transient results are
experienced with this thermal model. Tests indicate the model
accuracy to have less than 10 percent error. Output interaction
with an adjacent output is believed to be the main contributor to
the thermal inaccuracy. Tests indicate little or no detectable
thermal affects caused by distant output transistors isolated by
one or more other outputs. Tests were conducted with the
device mounted on a typical PC board placed horizontally in a
33 cubic inch still air enclosure. The PC board was made of FR4
material measuring 2.5 by 2.5 inches, having double sided
circuit traces of 1.0 ounce copper soldered to each device pin.
The board temperature was measured with thermal couple
soldered to the board surface one inch away from the center of
the device. The ambient temperature of the enclosure was
measured with a second thermal couple located over the center
of one inch distance from device.
Current
Area (I
A
)
V
PWR
Time
GND
Drain-to-Source ON
Voltage (V
DS(on)
)
Drain Current
(I
D
= 0.5A)
Drain-to-Source Clamp
Voltage (V
CL
= 65 V)
Drain Voltage
Clamp Energy
(E
J
= I
A
x V
CL
x t)
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC33298 Eight Output Switch with Serial Peripheral Interface I/O(帶SPI接口的八輸出開關)
MC33385 QUAD LOW SIDE DRIVER(四低端驅動器)
MC33388 Fault Tolerant CAN Interface(容錯CAN接口)
MC33389 System Basis Chip with Low Speed Fault Tolerant CAN(帶低速容錯CAN接口的系統基片)
MC33390 J-1850 SERIAL TRANSCEIVER(串行J-1850總線收發器)
相關代理商/技術參數
參數描述
MC33291DW 功能描述:IC SWITCH 8X L-SIDE W/SPI 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR)
MC33291DWR2 功能描述:IC SWITCH 8X L-SIDE W/SPI 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR)
MC33291LDW 功能描述:IC SWITCH 8X L-SIDE W/SPI 24SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR)
MC33292 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2/W NOTCHED 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2C/W NOTCHED 制造商:PRIVATE LABEL 功能描述:HEATSINK TO220 10.2C/W NOTCHED, Packages Cooled:TO-220, Thermal Resistance:10.2 制造商:SPC Multicomp 功能描述:HEAT SINK, Packages Cooled:TO-220, Thermal Resistance:10.2C/W, External Height - Imperial:1.496", External Height - Metric:38mm, External Width - Imperial:1.358", External Width - Metric:34.5mm, External Length - Imperial:0.492" , RoHS Compliant: Yes
MC33293 制造商:SPC Multicomp 功能描述:CLIP 001 制造商:SPC Multicomp 功能描述:CLIP; Fixing Type:Clip; For Use With:Heat Sinks (MC33285, MC33286, MC33287, MC33288, MC33289, MC33290, MC33291, MC33292); External Length:37.08mm; External Width:3.99mm; Clip Style:Mounting Clip; Length:37.08mm ;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*