- 您現在的位置：買賣IC網 > PDF目錄371020 > MC33023DW (MOTOROLA INC) High Speed Single-Ended PWM Controller PDF資料下載
參數資料
| 型號： | MC33023DW |
| 廠商： | MOTOROLA INC |
| 元件分類： | 穩(wěn)壓器 |
| 英文描述： | High Speed Single-Ended PWM Controller |
| 中文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | PLASTIC, SO-16 |
| 文件頁數： | 9/19頁 |
| 文件大?。?/td> | 470K |
| 代理商： | MC33023DW |
MC34023 MC33023
9
MOTOROLA ANALOG IC DEVICE DATA
Undervoltage Lockout
There are two undervoltage lockout circuits within the IC.
The first senses VCC and the second Vref. During power–up,
VCC must exceed 9.2 V and Vref must exceed 4.2 V before
the outputs can be enabled and the Soft–Start latch released.
If VCC falls below 8.4 V or Vref falls below 3.6 V, the outputs
are disabled and the Soft–Start latch is activated. When the
UVLO is active, the part is in a low current standby mode
allowing the IC to have an off–line bootstrap start–up circuit.
Typical start–up current is 500
μ
A.
Output
The MC34023 has a high current totem pole output
specifically designed for direct drive of power MOSFETs. It is
capable of up to
±
2.0 A peak drive current with a typical rise
and fall time of 30 ns driving a 1.0 nF load.
Separate pins for VC and Power Ground are provided.
With proper implementation, a significant reduction of
switching transient noise imposed on the control circuitry is
possible. The separate VC supply input also allows the
designer added flexibility in tailoring the drive voltage
independent of VCC.
Reference
A 5.1 V bandgap reference is pinned out and is trimmed to
an initial accuracy of
±
1.0% at 25
°
C. This reference has short
circuit protection and can source in excess of 10 mA for
powering additional control system circuitry.
Design Considerations
Do not attempt to construct the converter on
wire–wrap or plug–in prototype boards.
With high
frequency, high power, switching power supplies it is
imperative to have separate current loops for the signal paths
and for the power paths. The printed circuit layout should
contain a ground plane with low current signal and high
current switch and output grounds returning on separate
paths back to the input filter capacitor. Shown in Figure 35 is
a printed circuit layout of the application circuit. Note how the
power and ground traces are run. All bypass capacitors and
snubbers should be connected as close as possible to the
specific part in question. The PC board lead lengths must be
less than 0.5 inches for effective bypassing for snubbing.
Instabilities
In current mode control, an instability can be encountered
at any given duty cycle. The instability is caused by the
current feedback loop. It has been shown that the instability is
caused by a double pole at half the switching frequency. If an
external ramp (Se) is added to the on–time ramp (Sn) of the
current–sense waveform, stability can be achieved.
One must be careful not to add too much ramp
compensation. If too much is added the system will start to
perform like a voltage mode regulator. All benefits of current
mode control will be lost. Figure 25 is an example of one way
in which external ramp compensation can be implemented.
1.25 V
Figure 20. Ramp Compensation
Current
Signal Sn
Ramp Compensation
Ramp Input
Ramp
Compensation Se
A simple equation can be used to calculate the amount of
external ramp slope necessary to add that will achieve
stability in the current loop. For the following equations, the
calculated values for the application circuit in Figure 34 are
also shown.
Se
VO
L
NS
NP
(RS)A
i
where:
= DC output voltage
= number of power transformer primary
=
or secondary turns
= gain of the current sense network
=
(see Figures 23 and 24)
= output inductor
= current sense resistance
VO
NP, NS
Ai
L
RS
= 0.115 V/ms
For the application circuit: Se
5
1.8
μ
2
相關PDF資料 |
PDF描述 |
|---|---|
| MC33023P | High Speed Single-Ended PWM Controller |
| MC34023P | High Speed Single-Ended PWM Controller |
| MC3303D | QUAD DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERS |
| MC3403D | LOW POWER QUAD BIPOLAR OPERATIONAL AMPLIFIERS |
| MC3303D | QUAD DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33023DWG | 功能描述:電流型 PWM 控制器 Single Ended Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33023DWR2 | 功能描述:電流型 PWM 控制器 Single Ended Voltage RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33023DWR2G | 功能描述:電流型 PWM 控制器 Single Ended Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33023P | 制造商:Motorola 功能描述:MOTOROLA S1I2F |
| MC33024 | 制造商:SPC Multicomp 功能描述:FINGER GUARD 制造商:SPC Multicomp 功能描述:FINGER GUARD; For Use With:127mm Axial Fans; Fan Size:127mm; Fixing Centers:113.3mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Chrome; External Depth:5.5mm; External Height:115.6mm; External Width:115.6mm ;RoHS Compliant: Yes |
發(fā)布緊急采購，3分鐘左右您將得到回復。