- 您現在的位置：買賣IC網 > PDF目錄371014 > MC145159FN1 (MOTOROLA INC) Serial-Input PLL Frequency Synthesizer with Aanalog Phase Detector PDF資料下載
參數資料
| 型號： | MC145159FN1 |
| 廠商： | MOTOROLA INC |
| 元件分類： | XO, clock |
| 英文描述： | Serial-Input PLL Frequency Synthesizer with Aanalog Phase Detector |
| 中文描述： | PLL FREQUENCY SYNTHESIZER, PQCC20 |
| 封裝： | PLASTIC, LCC-20 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 223K |
| 代理商： | MC145159FN1 |
MC145159–1
MOTOROLA
5
PIN DESCRIPTIONS
INPUT PINS
OSCin, OSCout
Oscillator Input and Oscillator Output (PDIP, SOG –
Pins 2, 3; SSOP – Pins 7, 8)
These pins form an on–chip reference oscillator when
connected to terminals of an external parallel–resonant
crystal. Frequency–setting capacitors of appropriate value
must be connected from OSCin to VSS and OSCout to
VSS. OSCin may also serve as input for an externally–gen-
erated reference signal. This signal will typically be ac
coupled to OSCin, but for larger amplitude signals (standard
CMOS logic levels), dc coupling may also be used. In the
external reference mode, no connection is required to
OSCout.
fin
Frequency Input (PDIP, SOG – Pin 10, SSOP – Pin 15)
Input to the positive edge triggered divide–by–N and di-
vide–by–A counters. fin is typically derived from a dual–
modulus prescaler and is ac coupled. This input has an
inverter biased in the linear region to allow use with ac
coupled signals as low as 500 mV peak–to–peak or direct
coupled signals swinging from VDD to VSS.
DATA
Serial Data Input (PDIP, SOG – Pin 12, SSOP – Pin 17)
Counter and control information is shifted into this input.
The last data bit entered goes into the one–bit control shift
register. A logic 1 allows the reference counter information to
be loaded into its 14–bit latch when ENB goes high. A logic 0
entered as the control bit disables the reference counter
latch. The divide–by–A/divide–by–N counter latch is loaded,
regardless of the contents of the control register, when ENB
goes high. The data entry format is shown in Figure 1.
ENB
Transparent Latch Enable (PDIP, SOG – Pin 13,
SSOP – Pin 18)
A logic high on this input allows data to be entered into the
divide–by–A/divide–by–N latch and, if the control bit is high,
into the reference counter latch. Counter programming is
unaffected when ENB is low. ENB should be kept normally
low and pulsed high to transfer data to the latches.
CLK
Shift Register Clock (PDIP, SOG – Pin 11, SSOP – Pin 16)
A low–to–high transition on this input shifts data from the
serial data input into the shift registers.
COMPONENT PINS
CR
Ramp Capacitor (PDIP, SOG – Pin 15, SSOP – Pin 20)
The capacitor connected from this pin to VSS
′
is charged
linearly, at a rate determined by RR. The voltage on this
capacitor is proportional to the phase difference of the
frequencies present at the internal phase detector inputs. A
polystyrene or mylar capacitor is recommended.
RR
Ramp Current Bias Resistor (PDIP, SOG – Pin 20,
SSOP – Pin 5)
A resistor connected from this pin to VSS
′
determines the
rate at which the ramp capacitor is charged, thereby affecting
the phase detector gain (see Figure 2).
CH
Hold Capacitor (PDIP, SOG – Pin 18, SSOP – Pin 3)
The charge stored on the ramp capacitor is transferred to
the capacitor connected from this pin to either VDD
′
or VSS
′
.
The ratio of CR to CH should be large enough to have no
effect on the phase detector gain (CR > 10 CH). A low–leak-
age capacitor should be used.
RO
Output Bias Current Resistor (PDIP, SOG – Pin 1,
SSOP – Pin 6)
A resistor connected from this pin to VSS
′
biases the output
N–Channel transistor, thereby setting a current sink on the
analog phase detector output. This resistor adjusts the
APDout bias current (see Figure 3).
OUTPUT PINS
APDout
Analog Phase Detector Output (PDIP, SOG – Pin 17,
SSOP – Pin 2)
This output produces a voltage that controls an external
VCO. The voltage range of this output (VDD = + 9 V) is from
below + 0.5 V to + 8 V or more. The source impedance of this
output is the equivalent of a source follower with an exter-
nally variable source resistor. The source resistor depends
upon the output bias current controlled by the output bias
current resistor, RO. The bias current is adjustable from
0.01 mA to 0.5 mA. The output voltage is not more than
1.05 V below the sampled point on the ramp. With a constant
sample of the ramp voltage at 9 V and the hold capacitor of
50 pF, the instantaneous output ripple is about 5 mV peak–
to–peak.
Figure 1. Data Entry Format
相關PDF資料 |
PDF描述 |
|---|---|
| MC145159DW1 | Serial-Input PLL Frequency Synthesizer with Aanalog Phase Detector |
| MC14515BCL | 4-Bit Transparent Latch/4-to-16 Line Decoder |
| MC14515 | 4-Bit Transparent Latch/4-to-16 Line Decoder |
| MC14514 | 4-Bit Transparent Latch/4-to-16 Line Decoder |
| MC14514BDWR2 | 4-Bit Transparent Latch/4-to-16 Line Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC145159FN1R2 | 制造商:Motorola Inc 功能描述: |
| MC145159P1 | 制造商:Motorola Inc 功能描述: |
| MC14515BCP | 功能描述:編碼器、解碼器、復用器和解復用器 3-18V 4-Bit RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| MC14515BCPG | 功能描述:編碼器、解碼器、復用器和解復用器 3-18V 4-Bit Transparent RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| MC14515BDW | 制造商:ON Semiconductor 功能描述:Latch/Decoder/Demultiplexer Single 4-to-16 24-Pin SOIC Rail |
發布緊急采購，3分鐘左右您將得到回復。