- 您現在的位置：買賣IC網 > PDF目錄181332 > MC145011DW (FREESCALE SEMICONDUCTOR INC) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | MC145011DW |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | PLASTIC, SOIC-16 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 346K |
| 代理商： | MC145011DW |
Sensors
Freescale Semiconductor
5
MC145011
4
STROBE
This output provides a strobed, regulated voltage referenced to VDD. The temperature coefficient of this voltage is
± 0.2% °C maximum from - 10° to 60°C. The supply-voltage coefficient (line regulation) is ± 0.2%/V maximum from 6 to
12 V. Strobe is tied to external resistor string R8, R9, and R10.
5
VDD
This pin is connected to the positive supply potential and may range from + 6 to + 12 V with respect to VSS.
6
IRED
This output provides pulsed base current for external NPN transistor Q1 used as the infrared emitter driver. Q1 must
have
β ≥ 100. At 10 mA, the temperature coefficient of the output voltage is typically + 0.5%/°C from - 10° to 60°C. The
supply-voltage coefficient (line regulation) is
± 0.2%/V maximum from 6 to 12 V. The IRED pulse width (active-high) is
determined by external components R1 and C3. With a 100 k
/1500 pF combination, the nominal width is 105 s.
To minimize noise impact, IRED is not active when the visible LED and horn outputs are active. IRED is active near the
end of Strobe pulses for Smoke Tests, Chamber Sensitivity Test, and Pushbutton Test.
7
I/O
This pin can be used to connect up to 40 units together in a wired-OR configuration for common signaling. VSS is used
as the return. An on-chip current sink minimizes noise pick up during non-smoke conditions and eliminates the need for
an external pull-down resistor to complete the wired-OR. Remote units at lower supply voltages do not draw excessive
current from a sending unit at a higher supply voltage.
I/O can also be used to activate escape lights, auxiliary alarms, remote alarms, and/or auto-dialers.
As an input, this pin feeds a positive-edge-triggered flip-flop whose output is sampled nominally every 625 ms during
standby (using the recommended component values). A local-smoke condition or the pushbutton-test mode forces this
current-limited output to source current. All input signals are ignored when I/O is sourcing current.
If unused, I/O must be left unconnected.
8
BRASS
This half of the push-pull driver output is connected to the metal support electrode of a piezoelectric audio transducer
and to the horn-starting resistor. A continuous modulated tone from the transducer is a smoke alarm indicating either
local or remote smoke. A short beep or chirp is a trouble alarm indicating a low supply or degraded chamber sensitivity.
9
SILVER
This half of the push-pull driver output is connected to the ceramic electrode of a piezoelectric transducer and to the
horn-starting capacitor.
10
FEEDBACK This input is connected to both the feedback electrode of a self-resonating piezoelectric transducer and the horn-starting
resistor and capacitor through current-limiting resistor R4. If unused, this pin must be tied to VSS or VDD.
11
LED
This active-low open-drain output directly drives an external visible LED.
The load for the low-supply test is applied by this output. This low-supply test is non-coincident with the smoke tests,
chamber sensitivity test, pushbutton test, or any alarm signals.
The LED also provides a visual indication of the detector status as follows, assuming the component values shown in
Figure 8:
Standby (includes low-supply and chamber sensitivity tests) - constantly illuminated
Local Smoke - constantly extinguished
Remote Smoke - constantly illuminated
Pushbutton Test - constantly extinguished (system OK); constantly illuminated (system problem)
12
OSC
This pin is used in conjunction with external resistor R2 (10 M
) to VDD and external capacitor C3 (1500 pF) to VDD to
form an oscillator with a nominal period of 10.5 ms.
13
R1
This pin is used in conjunction with resistor R1 (100 k
) to pin 12 and C3 (1500 pF, see pin 12 description) to determine
the IRED pulse width. With this RC combination, the nominal pulse width is 105
s.
14
VSS
This pin is the negative supply potential and the return for the I/O pin. Pin 14 is usually tied to ground.
15
LOW-
SUPPLY
TRIP
This pin is connected to an external voltage which determines the low-supply alarm threshold. The trip voltage is
obtained through a resistor divider connected between the VDD and LED pins. The low-supply alarm threshold voltage
(in volts)
≈ (5R7/R6) + 5 where R6 and R7 are in the same units.
16
TEST
This input has an on-chip pull-down device and is used to manually invoke a test mode.
The Pushbutton Test mode is initiated by a high level at pin 16 (usually depression of a S.P.S.T. normally-open
pushbutton switch to VDD). After one oscillator cycle, IRED pulses approximately every 336 ms, regardless of the
presence of smoke. Additionally, the amplifier gain is increased by automatic selection of C1. Therefore, the background
reflections in the smoke chamber may be interpreted as smoke, generating a simulated-smoke condition. After the
second IRED pulse, a successful test activates the horn-driver and I/O circuits. The active I/O allows remote signaling
for system testing. When the Pushbutton Test switch is released, the Test input returns to VSS due to the on-chip pull-
down device. After one oscillator cycle, the amplifier gain returns to normal, thereby removing the simulated-smoke
condition. After two additional IRED pulses, less than a second, the IC exits the alarm mode and returns to standby
timing.
Table 4. Pin Description (Continued)
Pin No.
Pin Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MC2850-13-1 | 0.1 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MC33269DT-5 | 5 V FIXED POSITIVE LDO REGULATOR, 1.35 V DROPOUT, PSSO2 |
| MC33269D-5 | 5 V FIXED POSITIVE LDO REGULATOR, 1.35 V DROPOUT, PDSO8 |
| MC33269ST-5 | 5 V FIXED POSITIVE LDO REGULATOR, 1.35 V DROPOUT, PDSO4 |
| MC3346P | 5 CHANNEL, Si, NPN, RF POWER TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC145011ED | 功能描述:光電傳感器 SMOKE DETECTOR RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON |
| MC145011P | 功能描述:IC SMOKE DETECT PHOTOELEC 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC145012DW | 功能描述:IC SMOKE DETECT WITH I/O 16SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC145012DWR2 | 制造商:Rochester Electronics LLC 功能描述:PHOTO SMKE DET/NFPA TONE - Bulk 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
| MC145012ED | 功能描述:煙霧報警器 SM DETECTOR W/NFPA TONE RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感應方式:Photoelectric 工作電源電壓:24 V 輸出信號類型: |
發布緊急采購，3分鐘左右您將得到回復。