- 您現在的位置：買賣IC網 > PDF目錄385565 > MC14067BDW (ON SEMICONDUCTOR) Analog Multiplexers/Demultiplexers PDF資料下載
參數資料
| 型號： | MC14067BDW |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Analog Multiplexers/Demultiplexers |
| 中文描述： | 16-CHANNEL, SGL ENDED MULTIPLEXER, PDSO24 |
| 封裝： | SOIC-24 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 239K |
| 代理商： | MC14067BDW |
MC14067B
http://onsemi.com
9
APPLICATIONS INFORMATION
Figure
Multiplexer/Demultiplexer. The 0–to–5 volt Digital Control
signal is used to directly control a 5 V
p–p
analog signal.
The digital control logic levels are determined by V
DD
and V
SS
. The V
DD
voltage is the logic high voltage; the V
SS
voltage is logic low. For the example. V
DD
= + 5 V = logic
high at the control inputs; V
SS
= GND = 0 V = logic low.
The maximum analog signal level is determined by V
DD
and V
SS
. The analog voltage must swing neither higher than
V
DD
nor lower than V
SS
. The example shows a 5 V
p–p
A
illustrates
use
of
the
Analog
signal which allows no margin at either peak. If voltage
transients above V
DD
and/or below V
SS
are anticipated on
the analog channels, external diodes (D
x
) are recommended
as shown in Figure B. These diodes should be small signal
types able to absorb the maximum anticipated current surges
during clipping.
The absolute maximum potential difference between V
DD
and V
SS
is 18.0 volts. Most parameters are specified up to
15 V which is the recommended maximum difference
between V
DD
and V
SS
.
Figure A. Application Example
+5 V
V
DD
V
SS
5 V
p–p
ANALOG SIGNAL
0–TO–5 V DIGITAL
CONTROL SIGNALS
SWITCH
I/O
MC14067B
COMMON
O/I
5 V
p–p
ANALOG SIGNAL
+5.0 V
+
2.5 V
GND
+5 V
EXTERNAL
CMOS
DIGITAL
CIRCUITRY
Figure B. External Germanium or Schottky Clipping Diodes
V
DD
V
DD
V
SS
V
SS
D
X
D
X
D
X
D
X
SWITCH
I/O
COMMON
O/I
相關PDF資料 |
PDF描述 |
|---|---|
| MC14067BDWR2 | Analog Multiplexers/Demultiplexers |
| MC14070B | CMOS SSI Quad Exclusive “OR” and “NOR” Gates(四或門/或非門) |
| MC14077B | CMOS SSI Quad Exclusive “OR” and “NOR” Gates(四2輸入異或門) |
| MC14093B | Quad 2 Input "NAND" Schmitt Trigger(四2輸入施密特觸發正與非門) |
| MC14093 | IEEE 802.3af PoE HIGH POWER PD CONTROLLER 8-SO PowerPAD -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14067BDWG | 功能描述:多路器開關 IC 3-18V ANLG Mux/Demux -55 to 125deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14067BDWR2 | 功能描述:多路器開關 IC 3-18V ANLG Mux/Demux RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14067BDWR2G | 功能描述:多路器開關 IC 3-18V ANLG Mux/Demux -55 to 125deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14068B | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:B-Suffix Series CMOS Gates |
| MC14068BCL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:B-Suffix Series CMOS Gates |
發布緊急采購，3分鐘左右您將得到回復。