- 您現在的位置：買賣IC網 > PDF目錄385565 > MC14066BF (ON SEMICONDUCTOR) Replaced by TPS2300 : CompactPCI Hot Swap Power Manager Industrial Temp IC that meets the PICMG Standard 24-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MC14066BF |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Replaced by TPS2300 : CompactPCI Hot Swap Power Manager Industrial Temp IC that meets the PICMG Standard 24-TSSOP -40 to 85 |
| 中文描述： | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO14 |
| 封裝： | EIAJ, SOP-14 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 276K |
| 代理商： | MC14066BF |
MC14066B
http://onsemi.com
7
APPLICATIONS INFORMATION
Figure A illustrates use of the Analog Switch. The 0–
to–5 volt digital control signal is used to directly control a
5 volt peak–to–peak analog signal.
The digital control logic levels are determined by V
DD
and V
SS
. The V
DD
voltage is the logic high voltage, the V
SS
voltage is logic low. For the example, V
DD
= + 5 V = logic
high at the control inputs; V
SS
= GND = 0 V = logic low.
The maximum analog signal level is determined by V
DD
and V
SS
. The analog voltage must not swing higher than
V
DD
or lower than V
SS
.
The example shows a 5 volt peak–to–peak signal which
allows no margin at either peak. If voltage transients above
V
DD
and/or below V
SS
are anticipated on the analog
channels, external diodes (D
x
) are recommended as shown
in Figure B. These diodes should be small signal types able
to absorb the maximum anticipated current surges during
clipping.
The
absolute
maximum potential difference between
V
DD
and V
SS
is 18.0 volts. Most parameters are specified up
to 15 volts which is the
recommended
maximum difference
between V
DD
and V
SS
.
Figure A. Application Example
+5 V
V
DD
V
SS
5 V
p–p
ANALOG SIGNAL
0–TO–5 V DIGITAL
CONTROL SIGNALS
SWITCH
IN
MC14066B
SWITCH
OUT
5 V
p–p
ANALOG SIGNAL
+5.0 V
+
2.5 V
GND
+5 V
EXTERNAL
CMOS
DIGITAL
CIRCUITRY
Figure B. External Germanium or Schottky Clipping Diodes
V
DD
V
DD
V
SS
V
SS
D
X
D
X
D
X
D
X
SWITCH
IN
SWITCH
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| MC14066BFEL | Replaced by TPS2300 : CompactPCI Hot Swap Power Manager Industrial Temp IC that meets the PICMG Standard 24-TSSOP -40 to 85 |
| MC14067BCP | Analog Multiplexers/Demultiplexers |
| MC14067BDW | Analog Multiplexers/Demultiplexers |
| MC14067BDWR2 | Analog Multiplexers/Demultiplexers |
| MC14070B | CMOS SSI Quad Exclusive “OR” and “NOR” Gates(四或門/或非門) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14066BFEL | 功能描述:多路器開關 IC 3-18V Quad Analog SW RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14066BFELG | 功能描述:多路器開關 IC 3-18V Quad Analog SW -55 to 125deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14066BFG | 功能描述:多路器開關 IC 3-18V Quad Analog SW -55 to 125deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MC14066BFL1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC14066BFR1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。